===================================================================
@@ -29,6 +29,9 @@
obj-$(CONFIG_GENERATE_ACPI_TABLES) += acpi_tables.o
obj-$(CONFIG_GENERATE_ACPI_TABLES) += fadt.o
+# This is debug message for products of Technexion.
+obj-y += tn_post_code.o
+
# This is part of the conversion to init-obj and away from included code.
initobj-y += crt0.o
===================================================================
@@ -100,6 +100,10 @@
#include "cpu/amd/model_fxx/fidvid.c"
+#define TECHNEXION_EARLY_SETUP
+#include "tn_post_code.c"
+
+
#if CONFIG_USE_FALLBACK_IMAGE == 1
#include "northbridge/amd/amdk8/early_ht.c"
@@ -161,6 +165,8 @@
struct cpuid_result cpuid1;
struct sys_info *sysinfo = (struct sys_info *)(CONFIG_DCACHE_RAM_BASE + CONFIG_DCACHE_RAM_SIZE - CONFIG_DCACHE_RAM_GLOBAL_VAR_SIZE);
+ technexion_post_code_init();
+ technexion_post_code(LED_MESSAGE_START);
if (bist == 0) {
bsp_apicid = init_cpus(cpu_init_detectedx, sysinfo);
@@ -233,7 +239,11 @@
/* It's the time to set ctrl now; */
printk_debug("sysinfo->nodes: %2x sysinfo->ctrl: %2x spd_addr: %2x\n",
sysinfo->nodes, sysinfo->ctrl, spd_addr);
+
fill_mem_ctrl(sysinfo->nodes, sysinfo->ctrl, spd_addr);
+
+ technexion_post_code(LED_MESSAGE_RAM);
+
sdram_initialize(sysinfo->nodes, sysinfo->ctrl, sysinfo);
rs690_before_pci_init();
===================================================================
@@ -0,0 +1,207 @@
+
+#ifdef TECHNEXION_EARLY_SETUP
+
+#include <arch/cpu.h>
+#include "southbridge/amd/sb600/sb600.h"
+
+#else
+
+#include <device/pci.h>
+#include <device/pci_ids.h>
+
+#endif
+
+#include "tn_post_code.h"
+
+
+#ifdef TECHNEXION_EARLY_SETUP
+
+// TechNexion's Post Code Initially.
+void technexion_post_code_init(void)
+{
+ uint8_t reg8_data;
+ device_t dev=0;
+
+ // SMBus Module and ACPI Block (Device 20, Function 0)
+ dev = pci_locate_device(PCI_ID(PCI_VENDOR_ID_ATI, PCI_DEVICE_ID_ATI_SB600_SM), 0);
+
+ // LED[bit0]:GPIO0
+ // This is reference SB600 RRG 4.1.1 GPIO
+ reg8_data = pmio_read(0x60);
+ reg8_data |= (1<<7); // 1: GPIO if not used by SATA
+ pmio_write(0x60, reg8_data);
+
+ reg8_data = pci_read_config8(dev, 0x80);
+ reg8_data = ((reg8_data | (1<<0)) & ~(1<<4));
+ pci_write_config8(dev, 0x80, reg8_data);
+
+ // LED[bit1]:GPIO1
+ // This is reference SB600 RRG 4.1.1 GPIO
+ reg8_data = pci_read_config8(dev, 0x80);
+ reg8_data = ((reg8_data | (1<<1)) & ~(1<<5));
+ pci_write_config8(dev, 0x80, reg8_data);
+
+ // LED[bit2]:GPIO4
+ // This is reference SB600 RRG 4.1.1 GPIO
+ reg8_data = pmio_read(0x5e);
+ reg8_data &= ~(1<<7); // 0: GPIO if not used by SATA
+ pmio_write(0x5e, reg8_data);
+
+ reg8_data = pci_read_config8(dev, 0xa8);
+ reg8_data |= (1<<0);
+ pci_write_config8(dev, 0xa8, reg8_data);
+
+ reg8_data = pci_read_config8(dev, 0xa9);
+ reg8_data &= ~(1<<0);
+ pci_write_config8(dev, 0xa9, reg8_data);
+
+ // LED[bit3]:GPIO6
+ // This is reference SB600 RRG 4.1.1 GPIO
+ reg8_data = pmio_read(0x60);
+ reg8_data |= (1<<7); // 1: GPIO if not used by SATA
+ pmio_write(0x60, reg8_data);
+
+ reg8_data = pci_read_config8(dev, 0xa8);
+ reg8_data |= (1<<2);
+ pci_write_config8(dev, 0xa8, reg8_data);
+
+ reg8_data = pci_read_config8(dev, 0xa9);
+ reg8_data &= ~(1<<2);
+ pci_write_config8(dev, 0xa9, reg8_data);
+ // LED[bit4]:GPIO7
+ // This is reference SB600 RRG 4.1.1 GPIO
+ reg8_data = pci_read_config8(dev, 0xa8);
+ reg8_data |= (1<<3);
+ pci_write_config8(dev, 0xa8, reg8_data);
+
+ reg8_data = pci_read_config8(dev, 0xa9);
+ reg8_data &= ~(1<<3);
+ pci_write_config8(dev, 0xa9, reg8_data);
+
+ // LED[bit5]:GPIO8
+ // This is reference SB600 RRG 4.1.1 GPIO
+ reg8_data = pci_read_config8(dev, 0xa8);
+ reg8_data |= (1<<4);
+ pci_write_config8(dev, 0xa8, reg8_data);
+
+ reg8_data = pci_read_config8(dev, 0xa9);
+ reg8_data &= ~(1<<4);
+ pci_write_config8(dev, 0xa9, reg8_data);
+
+ // LED[bit6]:GPIO10
+ // This is reference SB600 RRG 4.1.1 GPIO
+ reg8_data = pci_read_config8(dev, 0xab);
+ reg8_data = ((reg8_data | (1<<0)) & ~(1<<1));
+ pci_write_config8(dev, 0xab, reg8_data);
+
+ // LED[bit7]:GPIO66
+ // This is reference SB600 RRG 4.1.1 GPIO
+ reg8_data = pmio_read(0x68);
+ reg8_data &= ~(1<<5); // 0: GPIO
+ pmio_write(0x68, reg8_data);
+
+ reg8_data = pci_read_config8(dev, 0x7e);
+ reg8_data = ((reg8_data | (1<<1)) & ~(1<<5));
+ pci_write_config8(dev, 0x7e, reg8_data);
+
+}
+
+#endif
+
+/* TechNexion's Post Code.
+ */
+void technexion_post_code(uint8_t udata8)
+{
+ uint8_t u8_data;
+ device_t dev=0;
+
+ // SMBus Module and ACPI Block (Device 20, Function 0)
+#ifdef TECHNEXION_EARLY_SETUP
+ dev = pci_locate_device(PCI_ID(PCI_VENDOR_ID_ATI, PCI_DEVICE_ID_ATI_SB600_SM), 0);
+#else
+ dev = dev_find_device(PCI_VENDOR_ID_ATI, PCI_DEVICE_ID_ATI_SB600_SM, 0);
+#endif
+
+ udata8 = ~(udata8);
+
+ // LED[bit0]:GPIO0
+ u8_data = pci_read_config8(dev, 0x80);
+ if (udata8 & 0x1) {
+ u8_data |= (1<<0);
+ }
+ else {
+ u8_data &= ~(1<<0);
+ }
+ pci_write_config8(dev, 0x80, u8_data);
+
+ // LED[bit1]:GPIO1
+ u8_data = pci_read_config8(dev, 0x80);
+ if (udata8 & 0x2) {
+ u8_data |= (1<<1);
+ }
+ else {
+ u8_data &= ~(1<<1);
+ }
+ pci_write_config8(dev, 0x80, u8_data);
+
+ // LED[bit2]:GPIO4
+ u8_data = pci_read_config8(dev, 0xa8);
+ if (udata8 & 0x4) {
+ u8_data |= (1<<0);
+ }
+ else {
+ u8_data &= ~(1<<0);
+ }
+ pci_write_config8(dev, 0xa8, u8_data);
+
+ // LED[bit3]:GPIO6
+ u8_data = pci_read_config8(dev, 0xa8);
+ if (udata8 & 0x8) {
+ u8_data |= (1<<2);
+ }
+ else {
+ u8_data &= ~(1<<2);
+ }
+ pci_write_config8(dev, 0xa8, u8_data);
+
+ // LED[bit4]:GPIO7
+ u8_data = pci_read_config8(dev, 0xa8);
+ if (udata8 & 0x10) {
+ u8_data |= (1<<3);
+ }
+ else {
+ u8_data &= ~(1<<3);
+ }
+ pci_write_config8(dev, 0xa8, u8_data);
+
+ // LED[bit5]:GPIO8
+ u8_data = pci_read_config8(dev, 0xa8);
+ if (udata8 & 0x20) {
+ u8_data |= (1<<4);
+ }
+ else {
+ u8_data &= ~(1<<4);
+ }
+ pci_write_config8(dev, 0xa8, u8_data);
+
+ // LED[bit6]:GPIO10
+ u8_data = pci_read_config8(dev, 0xab);
+ if (udata8 & 0x40) {
+ u8_data |= (1<<0);
+ }
+ else {
+ u8_data &= ~(1<<0);
+ }
+ pci_write_config8(dev, 0xab, u8_data);
+
+ // LED[bit7]:GPIO66
+ u8_data = pci_read_config8(dev, 0x7e);
+ if (udata8 & 0x80) {
+ u8_data |= (1<<1);
+ }
+ else {
+ u8_data &= ~(1<<1);
+ }
+ pci_write_config8(dev, 0x7e, u8_data);
+
+}
===================================================================
@@ -0,0 +1,15 @@
+
+
+#define LED_MESSAGE_START 0xFF
+#define LED_MESSAGE_FINISH 0x99
+#define LED_MESSAGE_RAM 0x01
+
+
+#ifdef TECHNEXION_EARLY_SETUP
+
+// TechNexion's Post Code Initially.
+void technexion_post_code_init(void);
+
+#endif
+
+void technexion_post_code(uint8_t udata8);
===================================================================
@@ -27,6 +27,7 @@
#include <device/pci_def.h>
#include <../southbridge/amd/sb600/sb600.h>
#include "chip.h"
+#include "tn_post_code.h"
#define ADT7461_ADDRESS 0x4C
#define ARA_ADDRESS 0x0C /* Alert Response Address */
@@ -44,12 +45,18 @@
#define ADT7461_write_byte(address, val) \
do_smbus_write_byte(SMBUS_IO_BASE, ADT7461_ADDRESS, address, val)
+/* previous
+ */
+void tim5690_enable(device_t dev);
+int add_mainboard_resources(struct lb_memory *mem);
+
+
uint64_t uma_memory_base, uma_memory_size;
/* set thermal config
*/
-static void set_thermal_config()
+static void set_thermal_config(void)
{
u8 byte;
u16 word;
@@ -176,6 +183,7 @@
lb_add_memory_range(mem, LB_MEM_RESERVED,
uma_memory_base, uma_memory_size);
#endif
+ technexion_post_code(LED_MESSAGE_FINISH);
}
struct chip_operations mainboard_ops = {
Hi, These are post codes for TIM-5690 LED debug message. It's easy show message. Thanks. Signed-off-by: Libra Li <libra.li@technexion.com>