Patchwork add h8dmr fam10 target

login
register
about
Submitter Ward Vandewege
Date 2009-07-28 03:24:37
Message ID <20090728032437.GA382@countzero.vandewege.net>
Download mbox | patch
Permalink /patch/78/
State Accepted
Headers show

Comments

Ward Vandewege - 2009-07-28 03:24:37
See attached.

There are a number of outstanding issues:

* we don't have the mc_patch_01000086.h CPU ucode file yet which is
referenced in a comment in src/mainboard/supermicro/h8dmr_fam10/Options.lb.
AMD has not released it yet. This is not a problem specific to this port.

* I'm seeing toolchain issues. I can't get this tree to compile correctly with
gcc 4.3 (32 bit) - there is an optimization issue where certain parts of the
CBFS code execute very slowly. With gcc 3.4 (32 bit) that slowness
disappears. This is probably not a problem related to this port specifically.

* setting CONFIG_DEFAULT_CONSOLE_LOGLEVEL lower than 8 simply hangs the boot
shortly after the warm reset triggered by the MCP55 code. I think this too
might be a toolchain problem (but I see it on gcc 3.4 as well as 4.3).

* during startup, the CPU cores talk through each other on serial for a
while. Again, not an issue specific to this port.

* to avoid very slow LZMA decompression I use this port with LZMA compression
disabled in CBFS. I'm not sure what's causing this particular slowness.

Thanks,
Ward.
Rudolf Marek - 2009-07-28 19:14:39
Hi,

Maybe your code sometimes is in the cachable range and sometimes not	.

Rudolf

Patch


Add supermicro h8dmr fam10 target. This is largely a mashup of the tyan s2912
fam10 and h8dmr k8 targets.

Many, many thanks to Marc, Myles, Patrick and Stepan for all their help with
this, and to Arne for doing the s2912 fam10 port.

Build and boot tested.

Signed-off-by: Ward Vandewege <ward@gnu.org>

Index: src/mainboard/supermicro/h8dmr_fam10/Config.lb
===================================================================
--- src/mainboard/supermicro/h8dmr_fam10/Config.lb	(revision 0)
+++ src/mainboard/supermicro/h8dmr_fam10/Config.lb	(revision 0)
@@ -0,0 +1,338 @@ 
+## 
+## This file is part of the coreboot project.
+## 
+## Copyright (C) 2007 AMD
+## Written by Yinghai Lu <yinghailu@amd.com> for AMD.
+## 
+## This program is free software; you can redistribute it and/or modify
+## it under the terms of the GNU General Public License as published by
+## the Free Software Foundation; either version 2 of the License, or
+## (at your option) any later version.
+## 
+## This program is distributed in the hope that it will be useful,
+## but WITHOUT ANY WARRANTY; without even the implied warranty of
+## MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+## GNU General Public License for more details.
+## 
+## You should have received a copy of the GNU General Public License
+## along with this program; if not, write to the Free Software
+## Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA  02110-1301 USA
+## 
+
+## CONFIG_XIP_ROM_SIZE must be a power of 2.
+# for testing with -O != s. FIXME
+#default CONFIG_XIP_ROM_SIZE = 128 * 1024
+default CONFIG_XIP_ROM_SIZE = 128 * 1024
+include /config/failovercalculation.lb
+
+arch i386 end 
+
+##
+## Build the objects we have code for in this directory.
+##
+
+driver mainboard.o
+#needed by irq_tables and mptable and acpi_tables
+object get_bus_conf.o
+
+if CONFIG_HAVE_MP_TABLE object mptable.o end
+if CONFIG_HAVE_PIRQ_TABLE object irq_tables.o end
+#object reset.o
+
+	if CONFIG_USE_INIT	
+		makerule ./auto.o
+		        depends "$(CONFIG_MAINBOARD)/cache_as_ram_auto.c option_table.h"
+        		action "$(CC) $(DISTRO_CFLAGS) $(CFLAGS) $(CPPFLAGS) -I$(TOP)/src -I. -c $(CONFIG_MAINBOARD)/cache_as_ram_auto.c -o $@"
+		end
+	else
+		makerule ./auto.inc
+        		depends "$(CONFIG_MAINBOARD)/cache_as_ram_auto.c option_table.h"
+		        action "$(CC) $(DISTRO_CFLAGS) $(CFLAGS) $(CPPFLAGS) $(DEBUG_CFLAGS) -I$(TOP)/src -I. -c -S $(CONFIG_MAINBOARD)/cache_as_ram_auto.c -o $@"
+		        action "perl -e 's/\.rodata/.rom.data/g' -pi $@"
+        		action "perl -e 's/\.text/.section .rom.text/g' -pi $@"
+		end
+	end
+
+if CONFIG_USE_FAILOVER_IMAGE
+else
+    if CONFIG_AP_CODE_IN_CAR
+        makerule ./apc_auto.o
+                depends "$(CONFIG_MAINBOARD)/apc_auto.c option_table.h"
+                action "$(CC) $(DISTRO_CFLAGS) $(CFLAGS) $(CPPFLAGS) -I$(TOP)/src -I. -c $(CONFIG_MAINBOARD)/apc_auto.c -o $@"
+        end
+    end
+end
+
+
+##
+## Build our 16 bit and 32 bit coreboot entry code
+##
+if CONFIG_HAVE_FAILOVER_BOOT
+    if CONFIG_USE_FAILOVER_IMAGE
+	mainboardinit cpu/x86/16bit/entry16.inc
+	ldscript /cpu/x86/16bit/entry16.lds
+    end
+else
+    if CONFIG_USE_FALLBACK_IMAGE
+	mainboardinit cpu/x86/16bit/entry16.inc
+	ldscript /cpu/x86/16bit/entry16.lds
+    end
+end
+
+mainboardinit cpu/x86/32bit/entry32.inc
+
+        if CONFIG_USE_INIT
+                ldscript /cpu/x86/32bit/entry32.lds
+        end
+
+        if CONFIG_USE_INIT
+                ldscript /cpu/amd/car/cache_as_ram.lds
+        end
+
+##
+## Build our reset vector (This is where coreboot is entered)
+##
+if CONFIG_HAVE_FAILOVER_BOOT
+    if CONFIG_USE_FAILOVER_IMAGE 
+	mainboardinit cpu/x86/16bit/reset16.inc 
+	ldscript /cpu/x86/16bit/reset16.lds 
+    else
+	mainboardinit cpu/x86/32bit/reset32.inc 
+	ldscript /cpu/x86/32bit/reset32.lds 
+    end
+else
+    if CONFIG_USE_FALLBACK_IMAGE 
+	mainboardinit cpu/x86/16bit/reset16.inc 
+	ldscript /cpu/x86/16bit/reset16.lds 
+    else
+	mainboardinit cpu/x86/32bit/reset32.inc 
+	ldscript /cpu/x86/32bit/reset32.lds 
+    end
+end
+
+##
+## Include an id string (For safe flashing)
+##
+mainboardinit southbridge/nvidia/mcp55/id.inc
+ldscript /southbridge/nvidia/mcp55/id.lds
+
+##
+## ROMSTRAP table for MCP55
+##
+if CONFIG_HAVE_FAILOVER_BOOT
+    if CONFIG_USE_FAILOVER_IMAGE 
+	mainboardinit southbridge/nvidia/mcp55/romstrap.inc
+	ldscript /southbridge/nvidia/mcp55/romstrap.lds
+    end
+else
+    if CONFIG_USE_FALLBACK_IMAGE 
+	mainboardinit southbridge/nvidia/mcp55/romstrap.inc
+	ldscript /southbridge/nvidia/mcp55/romstrap.lds
+    end
+end
+
+	##
+	## Setup Cache-As-Ram
+	##
+	mainboardinit cpu/amd/car/cache_as_ram.inc
+
+###
+### This is the early phase of coreboot startup 
+### Things are delicate and we test to see if we should
+### failover to another image.
+###
+if CONFIG_HAVE_FAILOVER_BOOT
+    if CONFIG_USE_FAILOVER_IMAGE
+		ldscript /arch/i386/lib/failover_failover.lds
+    end
+else
+    if CONFIG_USE_FALLBACK_IMAGE
+		ldscript /arch/i386/lib/failover.lds
+    end
+end
+
+##
+## Setup RAM
+##
+	if CONFIG_USE_INIT
+		initobject auto.o
+	else
+		mainboardinit ./auto.inc
+	end
+
+##
+## Include the secondary Configuration files 
+##
+config chip.h
+
+dir /southbridge/nvidia/mcp55
+
+chip northbridge/amd/amdfam10/root_complex
+        device apic_cluster 0 on
+                chip cpu/amd/socket_F_1207
+                        device apic 0 on end
+                end
+        end
+	device pci_domain 0 on
+		chip northbridge/amd/amdfam10 #mc0
+			device pci 18.0 on end
+			device pci 18.0 on end
+			device pci 18.0 on 
+        # SB on link 2.0
+			        chip southbridge/nvidia/mcp55 
+					device pci 0.0 on end   # HT
+                			device pci 1.0 on # LPC
+						chip superio/winbond/w83627hf
+							device pnp 2e.0 off #  Floppy
+                	                 			io 0x60 = 0x3f0
+                	                			irq 0x70 = 6
+                	                			drq 0x74 = 2
+							end
+                	        			device pnp 2e.1 off #  Parallel Port
+                	                 			io 0x60 = 0x378
+                	                			irq 0x70 = 7
+							end
+                	        			device pnp 2e.2 on #  Com1
+                	                 			io 0x60 = 0x3f8
+                	                			irq 0x70 = 4
+							end
+                	        			device pnp 2e.3 on #  Com2
+                	                 			io 0x60 = 0x2f8
+                	                			irq 0x70 = 3
+							end
+                	        			device pnp 2e.5 on #  Keyboard
+                	                 			io 0x60 = 0x60
+                	                 			io 0x62 = 0x64
+                	                			irq 0x70 = 1
+								irq 0x72 = 12
+							end
+                	        			device pnp 2e.6 off  # SFI 
+                	                 			io 0x62 = 0x100
+							end
+                	        			device pnp 2e.7 off #  GPIO_GAME_MIDI
+								io 0x60 = 0x220
+								io 0x62 = 0x300
+								irq 0x70 = 9
+							end						
+                	        			device pnp 2e.8 off end #  WDTO_PLED
+                	        			device pnp 2e.9 off end #  GPIO_SUSLED
+                	        			device pnp 2e.a off end #  ACPI
+                	        			device pnp 2e.b on #  HW Monitor
+ 					 			io 0x60 = 0x290
+								irq 0x70 = 5
+                					end
+						end
+					end
+			                device pci 1.1 on # SM 0
+                                                chip drivers/generic/generic #dimm 0-0-0
+                                                        device i2c 50 on end  
+                                                end              
+                                                chip drivers/generic/generic #dimm 0-0-1
+                                                        device i2c 51 on end
+                                                end     
+                                                chip drivers/generic/generic #dimm 0-1-0
+                                                        device i2c 52 on end
+                                                end             
+                                                chip drivers/generic/generic #dimm 0-1-1
+                                                        device i2c 53 on end
+                                                end              
+                                                chip drivers/generic/generic #dimm 1-0-0
+                                                        device i2c 54 on end
+                                                end     
+                                                chip drivers/generic/generic #dimm 1-0-1
+                                                        device i2c 55 on end
+                                                end     
+                                                chip drivers/generic/generic #dimm 1-1-0
+                                                        device i2c 56 on end
+                                                end     
+                                                chip drivers/generic/generic #dimm 1-1-1
+                                                        device i2c 57 on end
+                                                end 
+					end # SM
+                                        device pci 1.1 on # SM 1
+#PCI device smbus address will depend on addon pci device, do we need to scan_smbus_bus?
+#                                                chip drivers/generic/generic #PCIXA Slot1
+#                                                        device i2c 50 on end
+#                                                end
+#                                                chip drivers/generic/generic #PCIXB Slot1
+#                                                        device i2c 51 on end
+#                                                end     
+#                                                chip drivers/generic/generic #PCIXB Slot2
+#                                                        device i2c 52 on end
+#                                                end             
+#                                                chip drivers/generic/generic #PCI Slot1
+#                                                        device i2c 53 on end
+#                                                end              
+#                                                chip drivers/generic/generic #Master MCP55 PCI-E
+#                                                        device i2c 54 on end
+#                                                end     
+#                                                chip drivers/generic/generic #Slave MCP55 PCI-E
+#                                                        device i2c 55 on end
+#                                                end             
+                                                chip drivers/generic/generic #MAC EEPROM
+                                                        device i2c 51 on end
+                                                end 
+
+                                        end # SM 
+	                		device pci 2.0 on end # USB 1.1
+        	        		device pci 2.1 on end # USB 2
+                			device pci 4.0 on end # IDE
+	                		device pci 5.0 on end # SATA 0
+	                		device pci 5.1 on end # SATA 1
+	                		device pci 5.2 on end # SATA 2
+                			device pci 6.0 on  # PCI
+                                                chip drivers/pci/onboard
+                                                        device pci 6.0 on end
+							register "rom_address" = "0xfff00000" #for 1M
+#                                                        register "rom_address" = "0xfff80000" #for 512K
+                                                end
+					end
+        	        		device pci 6.1 on end # AZA
+	                		device pci 8.0 on end # NIC
+	                		device pci 9.0 on end # NIC
+        	       			device pci a.0 on  # PCI E 5
+						device pci 0.0 on #nec pci-x
+						end
+						device pci 0.1 on #nec pci-x
+							device pci 4.0 on end #scsi
+							device pci 4.1 on end #scsi
+						end
+					end
+        	       			device pci b.0 on end # PCI E 4
+                			device pci c.0 on end # PCI E 3
+                			device pci d.0 on end # PCI E 2
+                			device pci e.0 on end # PCI E 1
+        	       			device pci f.0 on end # PCI E 0
+	                                register "ide0_enable" = "1"
+                	                register "sata0_enable" = "1"
+                        	        register "sata1_enable" = "1"
+					register "mac_eeprom_smbus" = "3" # 1: smbus under 2e.8, 2: SM0 3: SM1
+					register "mac_eeprom_addr" = "0x51"
+				end
+			end #  device pci 18.0 
+			device pci 18.1 on end
+			device pci 18.2 on end
+			device pci 18.3 on end
+			device pci 18.4 on end
+#			device pci 19.0 on end
+#			device pci 19.1 on end
+#			device pci 19.2 on end
+#			device pci 19.3 on end
+#			device pci 19.4 on end
+		end # mc0
+		
+	end # PCI domain
+	
+#       chip drivers/generic/debug 
+#               device pnp 0.0 off end # chip name
+#                device pnp 0.1 on end # pci_regs_all
+#                device pnp 0.2 off end # mem
+#                device pnp 0.3 off end # cpuid
+#                device pnp 0.4 on end # smbus_regs_all
+#                device pnp 0.5 off end # dual core msr
+#                device pnp 0.6 off end # cache size
+#                device pnp 0.7 off end # tsc
+#                device pnp 0.8 off  end # io
+#                device pnp 0.9 on end # io
+#       end  
+end #root_complex
Index: src/mainboard/supermicro/h8dmr_fam10/mptable.c
===================================================================
--- src/mainboard/supermicro/h8dmr_fam10/mptable.c	(revision 0)
+++ src/mainboard/supermicro/h8dmr_fam10/mptable.c	(revision 0)
@@ -0,0 +1,162 @@ 
+/*
+ * This file is part of the coreboot project.
+ *
+ * Copyright (C) 2007 AMD
+ * Written by Yinghai Lu <yinghailu@amd.com> for AMD.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA  02110-1301 USA
+ */
+
+#include <console/console.h>
+#include <arch/smp/mpspec.h>
+#include <device/pci.h>
+#include <string.h>
+#include <stdint.h>
+
+#include <cpu/amd/amdfam10_sysconf.h>
+
+#include "mb_sysconf.h"
+
+extern void get_bus_conf(void);
+
+void *smp_write_config_table(void *v)
+{
+	static const char sig[4] = "PCMP";
+	static const char oem[8] = "SUPERMIC";
+	static const char productid[12] = "H8DMR       ";
+	struct mp_config_table *mc;
+	struct mb_sysconf_t *m;
+	unsigned sbdn;
+
+	int i,j;
+
+	mc = (void *)(((char *)v) + SMP_FLOATING_TABLE_LEN);
+	memset(mc, 0, sizeof(*mc));
+
+	memcpy(mc->mpc_signature, sig, sizeof(sig));
+	mc->mpc_length = sizeof(*mc); /* initially just the header */
+	mc->mpc_spec = 0x04;
+	mc->mpc_checksum = 0; /* not yet computed */
+	memcpy(mc->mpc_oem, oem, sizeof(oem));
+	memcpy(mc->mpc_productid, productid, sizeof(productid));
+	mc->mpc_oemptr = 0;
+	mc->mpc_oemsize = 0;
+	mc->mpc_entry_count = 0; /* No entries yet... */
+	mc->mpc_lapic = LAPIC_ADDR;
+	mc->mpe_length = 0;
+	mc->mpe_checksum = 0;
+	mc->reserved = 0;
+
+	smp_write_processors(mc);
+
+	get_bus_conf();
+	sbdn = sysconf.sbdn;
+	m = sysconf.mb;
+
+/*Bus:		Bus ID	Type*/
+	/* define bus and isa numbers */
+	for(j= 0; j < 256 ; j++) {
+		if(m->bus_type[j])
+			 smp_write_bus(mc, j, "PCI   ");
+	}
+	smp_write_bus(mc, m->bus_isa, "ISA   ");
+
+/*I/O APICs:	APIC ID	Version	State		Address*/
+	{
+		device_t dev;
+		struct resource *res;
+		uint32_t dword;
+
+		dev = dev_find_slot(m->bus_mcp55[0], PCI_DEVFN(sbdn+ 0x1,0));
+		if (dev) {
+			res = find_resource(dev, PCI_BASE_ADDRESS_1);
+			if (res) {
+				smp_write_ioapic(mc, m->apicid_mcp55, 0x11, res->base);
+			}
+
+			dword = 0x43c6c643;
+			pci_write_config32(dev, 0x7c, dword);
+
+			dword = 0x81001a00;
+			pci_write_config32(dev, 0x80, dword);
+
+			dword = 0xd00012d2;
+			pci_write_config32(dev, 0x84, dword);
+
+		}
+
+
+	}
+
+		   /*I/O Ints:	Type	Polarity    Trigger			Bus ID	 IRQ	APIC ID	PIN# */
+	smp_write_intsrc(mc, mp_ExtINT, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH, m->bus_isa, 0x0, m->apicid_mcp55, 0x0);
+	smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH,  m->bus_isa, 0x1, m->apicid_mcp55, 0x1);
+	smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH,  m->bus_isa, 0x0, m->apicid_mcp55, 0x2);
+	smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH,  m->bus_isa, 0x3, m->apicid_mcp55, 0x3);
+	smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH,  m->bus_isa, 0x4, m->apicid_mcp55, 0x4);
+	smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH,  m->bus_isa, 0x6, m->apicid_mcp55, 0x6);
+	smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH,  m->bus_isa, 0x7, m->apicid_mcp55, 0x7);
+	smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH,  m->bus_isa, 0x8, m->apicid_mcp55, 0x8);
+	smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH,  m->bus_isa, 0xc, m->apicid_mcp55, 0xc);
+	smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH,  m->bus_isa, 0xd, m->apicid_mcp55, 0xd);
+	smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH,  m->bus_isa, 0xe, m->apicid_mcp55, 0xe);
+	smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH,  m->bus_isa, 0xf, m->apicid_mcp55, 0xf);
+
+	smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, m->bus_mcp55[0], ((sbdn+1)<<2)|1, m->apicid_mcp55, 0xa);
+
+	smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, m->bus_mcp55[0], ((sbdn+2)<<2)|0, m->apicid_mcp55, 0x16); // 22
+
+	smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, m->bus_mcp55[0], ((sbdn+2)<<2)|1, m->apicid_mcp55, 0x17); // 23
+
+  smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, m->bus_mcp55[0], ((sbdn+6)<<2)|1, m->apicid_mcp55, 0x17); // 23
+
+	smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, m->bus_mcp55[0], ((sbdn+5)<<2)|0, m->apicid_mcp55, 0x14); // 20
+	smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, m->bus_mcp55[0], ((sbdn+5)<<2)|1, m->apicid_mcp55, 0x17); // 23
+	smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, m->bus_mcp55[0], ((sbdn+5)<<2)|2, m->apicid_mcp55, 0x15); // 21
+
+	smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, m->bus_mcp55[0], ((sbdn+8)<<2)|0, m->apicid_mcp55, 0x16); // 22
+	smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, m->bus_mcp55[0], ((sbdn+9)<<2)|0, m->apicid_mcp55, 0x15); // 21
+
+	for(j=7; j>=2; j--) {
+		if(!m->bus_mcp55[j]) continue;
+		for(i=0;i<4;i++) {
+			smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, m->bus_mcp55[j], (0x00<<2)|i, m->apicid_mcp55, 0x10 + (2+j+i+4-sbdn%4)%4);
+		}
+	}
+
+	for(j=0; j<1; j++)
+		for(i=0;i<4;i++) {
+			smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, m->bus_mcp55[1], ((0x04+j)<<2)|i, m->apicid_mcp55, 0x10 + (2+i+j)%4);
+		}
+
+/*Local Ints:	Type	Polarity    Trigger	Bus ID	 IRQ	APIC ID	PIN#*/
+	smp_write_intsrc(mc, mp_ExtINT, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH, m->bus_isa, 0x0, MP_APIC_ALL, 0x0);
+	smp_write_intsrc(mc, mp_NMI, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH, m->bus_isa, 0x0, MP_APIC_ALL, 0x1);
+	/* There is no extension information... */
+
+	/* Compute the checksums */
+	mc->mpe_checksum = smp_compute_checksum(smp_next_mpc_entry(mc), mc->mpe_length);
+	mc->mpc_checksum = smp_compute_checksum(mc, mc->mpc_length);
+	printk_debug("Wrote the mp table end at: %p - %p\n",
+		mc, smp_next_mpe_entry(mc));
+	return smp_next_mpe_entry(mc);
+}
+
+unsigned long write_smp_table(unsigned long addr)
+{
+	void *v;
+	v = smp_write_floating_table(addr);
+	return (unsigned long)smp_write_config_table(v);
+}
Index: src/mainboard/supermicro/h8dmr_fam10/resourcemap.c
===================================================================
--- src/mainboard/supermicro/h8dmr_fam10/resourcemap.c	(revision 0)
+++ src/mainboard/supermicro/h8dmr_fam10/resourcemap.c	(revision 0)
@@ -0,0 +1,286 @@ 
+/*
+ * This file is part of the coreboot project.
+ *
+ * Copyright (C) 2007 AMD
+ * Written by Yinghai Lu <yinghailu@amd.com> for AMD.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA  02110-1301 USA
+ */
+
+static void setup_mb_resource_map(void)
+{
+	static const unsigned int register_values[] = {
+		/* Careful set limit registers before base registers which contain the enables */
+		/* DRAM Limit i Registers
+		 * F1:0x44 i = 0
+		 * F1:0x4C i = 1
+		 * F1:0x54 i = 2
+		 * F1:0x5C i = 3
+		 * F1:0x64 i = 4
+		 * F1:0x6C i = 5
+		 * F1:0x74 i = 6
+		 * F1:0x7C i = 7
+		 * [ 2: 0] Destination Node ID
+		 *	   000 = Node 0
+		 *	   001 = Node 1
+		 *	   010 = Node 2
+		 *	   011 = Node 3
+		 *	   100 = Node 4
+		 *	   101 = Node 5
+		 *	   110 = Node 6
+		 *	   111 = Node 7
+		 * [ 7: 3] Reserved
+		 * [10: 8] Interleave select
+		 *	   specifies the values of A[14:12] to use with interleave enable.
+		 * [15:11] Reserved
+		 * [31:16] DRAM Limit Address i Bits 39-24
+		 *	   This field defines the upper address bits of a 40 bit  address
+		 *	   that define the end of the DRAM region.
+		 */
+		// PCI_ADDR(CONFIG_CBB, CONFIG_CDB, 1, 0x44), 0x0000f8f8, 0x00000000, // Don't touch it, we need it for CAR_FAM10
+		PCI_ADDR(CONFIG_CBB, CONFIG_CDB, 1, 0x4C), 0x0000f8f8, 0x00000001,
+		PCI_ADDR(CONFIG_CBB, CONFIG_CDB, 1, 0x54), 0x0000f8f8, 0x00000002,
+		PCI_ADDR(CONFIG_CBB, CONFIG_CDB, 1, 0x5C), 0x0000f8f8, 0x00000003,
+		PCI_ADDR(CONFIG_CBB, CONFIG_CDB, 1, 0x64), 0x0000f8f8, 0x00000004,
+		PCI_ADDR(CONFIG_CBB, CONFIG_CDB, 1, 0x6C), 0x0000f8f8, 0x00000005,
+		PCI_ADDR(CONFIG_CBB, CONFIG_CDB, 1, 0x74), 0x0000f8f8, 0x00000006,
+		PCI_ADDR(CONFIG_CBB, CONFIG_CDB, 1, 0x7C), 0x0000f8f8, 0x00000007,
+
+		/* DRAM Base i Registers
+		 * F1:0x40 i = 0
+		 * F1:0x48 i = 1
+		 * F1:0x50 i = 2
+		 * F1:0x58 i = 3
+		 * F1:0x60 i = 4
+		 * F1:0x68 i = 5
+		 * F1:0x70 i = 6
+		 * F1:0x78 i = 7
+		 * [ 0: 0] Read Enable
+		 *	   0 = Reads Disabled
+		 *	   1 = Reads Enabled
+		 * [ 1: 1] Write Enable
+		 *	   0 = Writes Disabled
+		 *	   1 = Writes Enabled
+		 * [ 7: 2] Reserved
+		 * [10: 8] Interleave Enable
+		 *	   000 = No interleave
+		 *	   001 = Interleave on A[12] (2 nodes)
+		 *	   010 = reserved
+		 *	   011 = Interleave on A[12] and A[14] (4 nodes)
+		 *	   100 = reserved
+		 *	   101 = reserved
+		 *	   110 = reserved
+		 *	   111 = Interleve on A[12] and A[13] and A[14] (8 nodes)
+		 * [15:11] Reserved
+		 * [13:16] DRAM Base Address i Bits 39-24
+		 *	   This field defines the upper address bits of a 40-bit address
+		 *	   that define the start of the DRAM region.
+		 */
+		// PCI_ADDR(CONFIG_CBB, CONFIG_CDB, 1, 0x40), 0x0000f8fc, 0x00000000, // don't touch it, we need it for CAR_FAM10
+		PCI_ADDR(CONFIG_CBB, CONFIG_CDB, 1, 0x48), 0x0000f8fc, 0x00000000,
+		PCI_ADDR(CONFIG_CBB, CONFIG_CDB, 1, 0x50), 0x0000f8fc, 0x00000000,
+		PCI_ADDR(CONFIG_CBB, CONFIG_CDB, 1, 0x58), 0x0000f8fc, 0x00000000,
+		PCI_ADDR(CONFIG_CBB, CONFIG_CDB, 1, 0x60), 0x0000f8fc, 0x00000000,
+		PCI_ADDR(CONFIG_CBB, CONFIG_CDB, 1, 0x68), 0x0000f8fc, 0x00000000,
+		PCI_ADDR(CONFIG_CBB, CONFIG_CDB, 1, 0x70), 0x0000f8fc, 0x00000000,
+		PCI_ADDR(CONFIG_CBB, CONFIG_CDB, 1, 0x78), 0x0000f8fc, 0x00000000,
+
+		/* Memory-Mapped I/O Limit i Registers
+		 * F1:0x84 i = 0
+		 * F1:0x8C i = 1
+		 * F1:0x94 i = 2
+		 * F1:0x9C i = 3
+		 * F1:0xA4 i = 4
+		 * F1:0xAC i = 5
+		 * F1:0xB4 i = 6
+		 * F1:0xBC i = 7
+		 * [ 2: 0] Destination Node ID
+		 *	   000 = Node 0
+		 *	   001 = Node 1
+		 *	   010 = Node 2
+		 *	   011 = Node 3
+		 *	   100 = Node 4
+		 *	   101 = Node 5
+		 *	   110 = Node 6
+		 *	   111 = Node 7
+		 * [ 3: 3] Reserved
+		 * [ 5: 4] Destination Link ID
+		 *	   00 = Link 0
+		 *	   01 = Link 1
+		 *	   10 = Link 2
+		 *	   11 = Reserved
+		 * [ 6: 6] Reserved
+		 * [ 7: 7] Non-Posted
+		 *	   0 = CPU writes may be posted
+		 *	   1 = CPU writes must be non-posted
+		 * [31: 8] Memory-Mapped I/O Limit Address i (39-16)
+		 *	   This field defines the upp adddress bits of a 40-bit address that
+		 *	   defines the end of a memory-mapped I/O region n
+		 */
+		PCI_ADDR(CONFIG_CBB, CONFIG_CDB, 1, 0x84), 0x00000048, 0x00000000,
+		PCI_ADDR(CONFIG_CBB, CONFIG_CDB, 1, 0x8C), 0x00000048, 0x00000000,
+		PCI_ADDR(CONFIG_CBB, CONFIG_CDB, 1, 0x94), 0x00000048, 0x00000000,
+		PCI_ADDR(CONFIG_CBB, CONFIG_CDB, 1, 0x9C), 0x00000048, 0x00000000,
+		PCI_ADDR(CONFIG_CBB, CONFIG_CDB, 1, 0xA4), 0x00000048, 0x00000000,
+		PCI_ADDR(CONFIG_CBB, CONFIG_CDB, 1, 0xAC), 0x00000048, 0x00000000,
+		PCI_ADDR(CONFIG_CBB, CONFIG_CDB, 1, 0xB4), 0x00000048, 0x00000000,
+//		PCI_ADDR(CONFIG_CBB, CONFIG_CDB, 1, 0xBC), 0x00000048, 0x00ffff00,
+
+		/* Memory-Mapped I/O Base i Registers
+		 * F1:0x80 i = 0
+		 * F1:0x88 i = 1
+		 * F1:0x90 i = 2
+		 * F1:0x98 i = 3
+		 * F1:0xA0 i = 4
+		 * F1:0xA8 i = 5
+		 * F1:0xB0 i = 6
+		 * F1:0xB8 i = 7
+		 * [ 0: 0] Read Enable
+		 *	   0 = Reads disabled
+		 *	   1 = Reads Enabled
+		 * [ 1: 1] Write Enable
+		 *	   0 = Writes disabled
+		 *	   1 = Writes Enabled
+		 * [ 2: 2] Cpu Disable
+		 *	   0 = Cpu can use this I/O range
+		 *	   1 = Cpu requests do not use this I/O range
+		 * [ 3: 3] Lock
+		 *	   0 = base/limit registers i are read/write
+		 *	   1 = base/limit registers i are read-only
+		 * [ 7: 4] Reserved
+		 * [31: 8] Memory-Mapped I/O Base Address i (39-16)
+		 *	   This field defines the upper address bits of a 40bit address 
+		 *	   that defines the start of memory-mapped I/O region i
+		 */
+		PCI_ADDR(CONFIG_CBB, CONFIG_CDB, 1, 0x80), 0x000000f0, 0x00000000,
+		PCI_ADDR(CONFIG_CBB, CONFIG_CDB, 1, 0x88), 0x000000f0, 0x00000000,
+		PCI_ADDR(CONFIG_CBB, CONFIG_CDB, 1, 0x90), 0x000000f0, 0x00000000,
+		PCI_ADDR(CONFIG_CBB, CONFIG_CDB, 1, 0x98), 0x000000f0, 0x00000000,
+		PCI_ADDR(CONFIG_CBB, CONFIG_CDB, 1, 0xA0), 0x000000f0, 0x00000000,
+		PCI_ADDR(CONFIG_CBB, CONFIG_CDB, 1, 0xA8), 0x000000f0, 0x00000000,
+		PCI_ADDR(CONFIG_CBB, CONFIG_CDB, 1, 0xB0), 0x000000f0, 0x00000000,
+//		PCI_ADDR(CONFIG_CBB, CONFIG_CDB, 1, 0xB8), 0x000000f0, 0x00fc0003,
+
+		/* PCI I/O Limit i Registers
+		 * F1:0xC4 i = 0
+		 * F1:0xCC i = 1
+		 * F1:0xD4 i = 2
+		 * F1:0xDC i = 3
+		 * [ 2: 0] Destination Node ID
+		 *	   000 = Node 0
+		 *	   001 = Node 1
+		 *	   010 = Node 2
+		 *	   011 = Node 3
+		 *	   100 = Node 4
+		 *	   101 = Node 5
+		 *	   110 = Node 6
+		 *	   111 = Node 7
+		 * [ 3: 3] Reserved
+		 * [ 5: 4] Destination Link ID
+		 *	   00 = Link 0
+		 *	   01 = Link 1
+		 *	   10 = Link 2
+		 *	   11 = reserved
+		 * [11: 6] Reserved
+		 * [24:12] PCI I/O Limit Address i
+		 *	   This field defines the end of PCI I/O region n
+		 * [31:25] Reserved
+		 */
+// WARD CHANGED
+		//PCI_ADDR(CONFIG_CBB, CONFIG_CDB, 1, 0xC4), 0xFE000FC8, 0x01fff020,
+		//PCI_ADDR(CONFIG_CBB, CONFIG_CDB, 1, 0xCC), 0xFE000FC8, 0x00000000, // need to talk to ANALOG of second CK804 to release PCI E reset
+		PCI_ADDR(CONFIG_CBB, CONFIG_CDB, 1, 0xD4), 0xFE000FC8, 0x00000000,
+		PCI_ADDR(CONFIG_CBB, CONFIG_CDB, 1, 0xDC), 0xFE000FC8, 0x00000000,
+
+		/* PCI I/O Base i Registers
+		 * F1:0xC0 i = 0
+		 * F1:0xC8 i = 1
+		 * F1:0xD0 i = 2
+		 * F1:0xD8 i = 3
+		 * [ 0: 0] Read Enable
+		 *	   0 = Reads Disabled
+		 *	   1 = Reads Enabled
+		 * [ 1: 1] Write Enable
+		 *	   0 = Writes Disabled
+		 *	   1 = Writes Enabled
+		 * [ 3: 2] Reserved
+		 * [ 4: 4] VGA Enable
+		 *	   0 = VGA matches Disabled
+		 *	   1 = matches all address < 64K and where A[9:0] is in the 
+		 *	       range 3B0-3BB or 3C0-3DF independen of the base & limit registers
+		 * [ 5: 5] ISA Enable
+		 *	   0 = ISA matches Disabled
+		 *	   1 = Blocks address < 64K and in the last 768 bytes of eack 1K block
+		 *	       from matching agains this base/limit pair
+		 * [11: 6] Reserved
+		 * [24:12] PCI I/O Base i
+		 *	   This field defines the start of PCI I/O region n 
+		 * [31:25] Reserved
+		 */
+		// WARD CHANGED
+		//PCI_ADDR(CONFIG_CBB, CONFIG_CDB, 1, 0xC0), 0xFE000FCC, 0x00000033,
+		//PCI_ADDR(CONFIG_CBB, CONFIG_CDB, 1, 0xC8), 0xFE000FCC, 0x00000000,
+		PCI_ADDR(CONFIG_CBB, CONFIG_CDB, 1, 0xD0), 0xFE000FCC, 0x00000000,
+		PCI_ADDR(CONFIG_CBB, CONFIG_CDB, 1, 0xD8), 0xFE000FCC, 0x00000000,
+
+		/* Config Base and Limit i Registers
+		 * F1:0xE0 i = 0
+		 * F1:0xE4 i = 1
+		 * F1:0xE8 i = 2
+		 * F1:0xEC i = 3
+		 * [ 0: 0] Read Enable
+		 *	   0 = Reads Disabled
+		 *	   1 = Reads Enabled
+		 * [ 1: 1] Write Enable
+		 *	   0 = Writes Disabled
+		 *	   1 = Writes Enabled
+		 * [ 2: 2] Device Number Compare Enable
+		 *	   0 = The ranges are based on bus number
+		 *	   1 = The ranges are ranges of devices on bus 0
+		 * [ 3: 3] Reserved
+		 * [ 6: 4] Destination Node
+		 *	   000 = Node 0
+		 *	   001 = Node 1
+		 *	   010 = Node 2
+		 *	   011 = Node 3
+		 *	   100 = Node 4
+		 *	   101 = Node 5
+		 *	   110 = Node 6
+		 *	   111 = Node 7
+		 * [ 7: 7] Reserved
+		 * [ 9: 8] Destination Link
+		 *	   00 = Link 0
+		 *	   01 = Link 1
+		 *	   10 = Link 2
+		 *	   11 - Reserved
+		 * [15:10] Reserved
+		 * [23:16] Bus Number Base i
+		 *	   This field defines the lowest bus number in configuration region i
+		 * [31:24] Bus Number Limit i
+		 *	   This field defines the highest bus number in configuration region i
+		 */
+		// WARD CHANGED
+		//PCI_ADDR(CONFIG_CBB, CONFIG_CDB, 1, 0xE0), 0x0000FC88, 0x3f000203, /* link 2 of cpu 0 --> Nvidia MCP55 Pro */
+		//PCI_ADDR(CONFIG_CBB, CONFIG_CDB, 1, 0xE4), 0x0000FC88, 0x00000000, 
+		PCI_ADDR(CONFIG_CBB, CONFIG_CDB, 1, 0xE8), 0x0000FC88, 0x00000000,
+		PCI_ADDR(CONFIG_CBB, CONFIG_CDB, 1, 0xEC), 0x0000FC88, 0x00000000, 
+
+	};
+
+	int max;
+	max = ARRAY_SIZE(register_values);
+	setup_resource_map(register_values, max);
+}
+
Index: src/mainboard/supermicro/h8dmr_fam10/irq_tables.c
===================================================================
--- src/mainboard/supermicro/h8dmr_fam10/irq_tables.c	(revision 0)
+++ src/mainboard/supermicro/h8dmr_fam10/irq_tables.c	(revision 0)
@@ -0,0 +1,138 @@ 
+/*
+ * This file is part of the coreboot project.
+ *
+ * Copyright (C) 2007 AMD
+ * Written by Yinghai Lu <yinghailu@amd.com> for AMD.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA  02110-1301 USA
+ */
+
+/* This file was generated by getpir.c, do not modify! 
+ * (but if you do, please run checkpir on it to verify)
+ * Contains the IRQ Routing Table dumped directly from your memory , wich BIOS sets up
+
+ * Documentation at : http://www.microsoft.com/hwdev/busbios/PCIIRQ.HTM
+*/
+#include <console/console.h>
+#include <device/pci.h>
+#include <string.h>
+#include <stdint.h>
+#include <arch/pirq_routing.h>
+
+#include <cpu/amd/amdfam10_sysconf.h>
+#include "mb_sysconf.h"
+
+static void write_pirq_info(struct irq_info *pirq_info, uint8_t bus, uint8_t devfn, uint8_t link0, uint16_t bitmap0, 
+		uint8_t link1, uint16_t bitmap1, uint8_t link2, uint16_t bitmap2,uint8_t link3, uint16_t bitmap3,
+		uint8_t slot, uint8_t rfu)
+{
+	pirq_info->bus = bus; 
+	pirq_info->devfn = devfn;
+		pirq_info->irq[0].link = link0;
+		pirq_info->irq[0].bitmap = bitmap0;
+		pirq_info->irq[1].link = link1;
+		pirq_info->irq[1].bitmap = bitmap1;
+		pirq_info->irq[2].link = link2;
+		pirq_info->irq[2].bitmap = bitmap2;
+		pirq_info->irq[3].link = link3;
+		pirq_info->irq[3].bitmap = bitmap3;
+	pirq_info->slot = slot;
+	pirq_info->rfu = rfu;
+}
+
+extern void get_bus_conf(void);
+
+unsigned long write_pirq_routing_table(unsigned long addr)
+{
+
+	struct irq_routing_table *pirq;
+	struct irq_info *pirq_info;
+	unsigned slot_num;
+	uint8_t *v;
+	struct mb_sysconf_t *m;
+	unsigned sbdn;
+
+	uint8_t sum=0;
+	int i;
+
+	get_bus_conf(); // it will find out all bus num and apic that share with mptable.c and mptable.c and acpi_tables.c
+	sbdn = sysconf.sbdn;
+	m = sysconf.mb;
+
+	/* Align the table to be 16 byte aligned. */
+	addr += 15;
+	addr &= ~15;
+
+	/* This table must be between 0xf0000 & 0x100000 */
+	printk_info("Writing IRQ routing tables to 0x%x...", addr);
+
+	pirq = (void *)(addr);
+	v = (uint8_t *)(addr);
+	
+	pirq->signature = PIRQ_SIGNATURE;
+	pirq->version  = PIRQ_VERSION;
+	
+	pirq->rtr_bus = m->bus_mcp55[0];
+	pirq->rtr_devfn = ((sbdn+6)<<3)|0;
+
+	pirq->exclusive_irqs = 0;
+	
+	pirq->rtr_vendor = 0x10de;
+	pirq->rtr_device = 0x0370;
+
+	pirq->miniport_data = 0;
+
+	memset(pirq->rfu, 0, sizeof(pirq->rfu));
+
+	pirq_info = (void *) ( &pirq->checksum + 1);
+	slot_num = 0;
+//pci bridge
+	write_pirq_info(pirq_info, m->bus_mcp55[0], ((sbdn+6)<<3)|0, 0x1, 0xdef8, 0x2, 0xdef8, 0x3, 0xdef8, 0x4, 0xdef8, 0, 0);
+	pirq_info++; slot_num++;
+	
+	for(i=1; i< sysconf.hc_possible_num; i++) {
+		if(!(sysconf.pci1234[i] & 0x1) ) continue;
+		unsigned busn = (sysconf.pci1234[i] >> 12) & 0xff;
+		unsigned devn = sysconf.hcdn[i] & 0xff;
+
+		write_pirq_info(pirq_info, busn, (devn<<3)|0, 0x1, 0xdef8, 0x2, 0xdef8, 0x3, 0xdef8, 0x4, 0xdef8, 0, 0);
+		pirq_info++; slot_num++;
+	}
+
+#if CONFIG_CBB
+	write_pirq_info(pirq_info, CONFIG_CBB, (0<<3)|0, 0x1, 0xdef8, 0x2, 0xdef8, 0x3, 0xdef8, 0x4, 0xdef8, 0, 0);
+	pirq_info++; slot_num++;
+	if(sysconf.nodes>32) {
+		write_pirq_info(pirq_info, CONFIG_CBB-1, (0<<3)|0, 0x1, 0xdef8, 0x2, 0xdef8, 0x3, 0xdef8, 0x4, 0xdef8, 0, 0);
+		pirq_info++; slot_num++;
+	}
+#endif
+
+	pirq->size = 32 + 16 * slot_num; 
+
+	for (i = 0; i < pirq->size; i++)
+		sum += v[i];	
+
+	sum = pirq->checksum - sum;
+
+	if (sum != pirq->checksum) {
+		pirq->checksum = sum;
+	}
+
+	printk_info("done.\n");
+
+	return	(unsigned long) pirq_info;
+
+}
Index: src/mainboard/supermicro/h8dmr_fam10/spd_addr.h
===================================================================
--- src/mainboard/supermicro/h8dmr_fam10/spd_addr.h	(revision 0)
+++ src/mainboard/supermicro/h8dmr_fam10/spd_addr.h	(revision 0)
@@ -0,0 +1,110 @@ 
+/*
+ * This file is part of the coreboot project.
+ *
+ * Copyright (C) 2007 Advanced Micro Devices, Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; version 2 of the License.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA  02110-1301 USA
+ */
+
+/**
+ * This file defines the SPD addresses for the mainboard. Must be included in
+ * cache_as_ram_auto.c
+ */
+
+#define RC00 0
+#define RC01 1
+#define RC02 2
+#define RC03 3
+#define RC04 4
+#define RC05 5
+#define RC06 6
+#define RC07 7
+#define RC08 8
+#define RC09 9
+#define RC10 10
+#define RC11 11
+#define RC12 12
+#define RC13 13
+#define RC14 14
+#define RC15 15
+#define RC16 16
+#define RC17 17
+#define RC18 18
+#define RC19 19
+#define RC20 20
+#define RC21 21
+#define RC22 22
+#define RC23 23
+#define RC24 24
+#define RC25 25
+#define RC26 26
+#define RC27 27
+#define RC28 28
+#define RC29 29
+#define RC30 30
+#define RC31 31
+
+#define RC32 32
+#define RC33 33
+#define RC34 34
+#define RC35 35
+#define RC36 36
+#define RC37 37
+#define RC38 38
+#define RC39 39
+#define RC40 40
+#define RC41 41
+#define RC42 42
+#define RC43 43
+#define RC44 44
+#define RC45 45
+#define RC46 46
+#define RC47 47
+#define RC48 48
+#define RC49 49
+#define RC50 50
+#define RC51 51
+#define RC52 52
+#define RC53 53
+#define RC54 54
+#define RC55 55
+#define RC56 56
+#define RC57 57
+#define RC58 58
+#define RC59 59
+#define RC60 60
+#define RC61 61
+#define RC62 62
+#define RC63 63
+
+
+#define DIMM0 0x50
+#define DIMM1 0x51
+#define DIMM2 0x52
+#define DIMM3 0x53
+#define DIMM4 0x54
+#define DIMM5 0x55
+#define DIMM6 0x56
+#define DIMM7 0x57
+
+
+static const u8 spd_addr[] = {
+	//first node
+	RC00, DIMM0, DIMM2, 0, 0, DIMM1, DIMM3, 0, 0,
+#if CONFIG_MAX_PHYSICAL_CPUS > 1
+	//second node
+	RC00, DIMM4, DIMM6, 0, 0, DIMM5, DIMM7, 0, 0,
+#endif
+};
+
Index: src/mainboard/supermicro/h8dmr_fam10/Options.lb
===================================================================
--- src/mainboard/supermicro/h8dmr_fam10/Options.lb	(revision 0)
+++ src/mainboard/supermicro/h8dmr_fam10/Options.lb	(revision 0)
@@ -0,0 +1,371 @@ 
+## 
+## This file is part of the coreboot project.
+## 
+## Copyright (C) 2007 AMD
+## Written by Yinghai Lu <yinghailu@amd.com> for AMD.
+## 
+## This program is free software; you can redistribute it and/or modify
+## it under the terms of the GNU General Public License as published by
+## the Free Software Foundation; either version 2 of the License, or
+## (at your option) any later version.
+## 
+## This program is distributed in the hope that it will be useful,
+## but WITHOUT ANY WARRANTY; without even the implied warranty of
+## MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+## GNU General Public License for more details.
+## 
+## You should have received a copy of the GNU General Public License
+## along with this program; if not, write to the Free Software
+## Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA  02110-1301 USA
+## 
+
+uses CONFIG_HAVE_MP_TABLE
+uses CONFIG_CBFS
+uses CONFIG_HAVE_PIRQ_TABLE
+uses CONFIG_HAVE_ACPI_TABLES
+uses CONFIG_HAVE_ACPI_RESUME
+uses CONFIG_ACPI_SSDTX_NUM
+uses CONFIG_USE_FALLBACK_IMAGE
+uses CONFIG_USE_FAILOVER_IMAGE
+uses CONFIG_HAVE_FALLBACK_BOOT
+uses CONFIG_HAVE_FAILOVER_BOOT
+uses CONFIG_HAVE_HARD_RESET
+uses CONFIG_IRQ_SLOT_COUNT
+uses CONFIG_HAVE_OPTION_TABLE
+uses CONFIG_MAX_CPUS
+uses CONFIG_MAX_PHYSICAL_CPUS
+uses CONFIG_LOGICAL_CPUS
+uses CONFIG_IOAPIC
+uses CONFIG_SMP
+uses CONFIG_FALLBACK_SIZE
+uses CONFIG_FAILOVER_SIZE
+uses CONFIG_ROM_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_IMAGE_SIZE
+uses CONFIG_ROM_SECTION_SIZE
+uses CONFIG_ROM_SECTION_OFFSET
+uses CONFIG_ROM_PAYLOAD
+uses CONFIG_ROM_PAYLOAD_START
+uses CONFIG_COMPRESSED_PAYLOAD_NRV2B
+uses CONFIG_COMPRESSED_PAYLOAD_LZMA
+uses CONFIG_PAYLOAD_SIZE
+uses CONFIG_ROMBASE
+uses CONFIG_XIP_ROM_SIZE
+uses CONFIG_XIP_ROM_BASE
+uses CONFIG_STACK_SIZE
+uses CONFIG_HEAP_SIZE
+uses CONFIG_USE_OPTION_TABLE
+uses CONFIG_LB_CKS_RANGE_START
+uses CONFIG_LB_CKS_RANGE_END
+uses CONFIG_LB_CKS_LOC
+uses CONFIG_MAINBOARD_PART_NUMBER
+uses CONFIG_MAINBOARD_VENDOR
+uses CONFIG_MAINBOARD
+uses CONFIG_MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID
+uses CONFIG_MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID
+uses COREBOOT_EXTRA_VERSION
+uses CONFIG_RAMBASE
+uses CONFIG_TTYS0_BAUD
+uses CONFIG_TTYS0_BASE
+uses CONFIG_TTYS0_LCS
+uses CONFIG_DEFAULT_CONSOLE_LOGLEVEL
+uses CONFIG_MAXIMUM_CONSOLE_LOGLEVEL
+uses CONFIG_MAINBOARD_POWER_ON_AFTER_POWER_FAIL
+uses CONFIG_CONSOLE_SERIAL8250
+uses CONFIG_HAVE_INIT_TIMER
+uses CONFIG_GDB_STUB
+uses CONFIG_CROSS_COMPILE
+uses CC
+uses HOSTCC
+uses CONFIG_OBJCOPY
+uses CONFIG_CONSOLE_VGA
+uses CONFIG_PCI_ROM_RUN
+uses CONFIG_HW_MEM_HOLE_SIZEK
+uses CONFIG_HW_MEM_HOLE_SIZE_AUTO_INC
+
+uses CONFIG_HT_CHAIN_UNITID_BASE
+uses CONFIG_HT_CHAIN_END_UNITID_BASE
+uses CONFIG_SB_HT_CHAIN_ON_BUS0
+uses CONFIG_SB_HT_CHAIN_UNITID_OFFSET_ONLY
+
+uses CONFIG_USE_DCACHE_RAM
+uses CONFIG_DCACHE_RAM_BASE
+uses CONFIG_DCACHE_RAM_SIZE
+uses CONFIG_DCACHE_RAM_GLOBAL_VAR_SIZE
+uses CONFIG_USE_INIT
+
+uses CONFIG_SERIAL_CPU_INIT
+
+uses CONFIG_ENABLE_APIC_EXT_ID
+uses CONFIG_APIC_ID_OFFSET
+uses CONFIG_LIFT_BSP_APIC_ID
+
+uses CONFIG_PCI_64BIT_PREF_MEM
+
+uses CONFIG_LB_MEM_TOPK
+
+uses CONFIG_UNCOMPRESSED
+
+uses CONFIG_PCI_BUS_SEGN_BITS
+
+uses CONFIG_AP_CODE_IN_CAR
+
+uses CONFIG_MEM_TRAIN_SEQ
+
+uses CONFIG_WAIT_BEFORE_CPUS_INIT
+
+uses CONFIG_AMDMCT
+
+uses CONFIG_USE_PRINTK_IN_CAR
+uses CONFIG_CAR_FAM10
+uses CONFIG_AMD_UCODE_PATCH_FILE
+
+###
+### Build options
+###
+
+##
+## CONFIG_ROM_SIZE is the size of boot ROM that this board will use.
+##
+default CONFIG_ROM_SIZE=1024*1024
+
+##
+## CONFIG_FALLBACK_SIZE is the amount of the ROM the ROM part of the fallback image will use
+default CONFIG_FALLBACK_SIZE=CONFIG_ROM_IMAGE_SIZE
+default CONFIG_FAILOVER_SIZE=0x02000
+
+#more 1M for pgtbl
+default CONFIG_LB_MEM_TOPK=16384
+
+##
+## Build code for the fallback boot
+##
+default CONFIG_HAVE_FALLBACK_BOOT=1
+default CONFIG_HAVE_FAILOVER_BOOT=1
+
+##
+## Build code to reset the motherboard from coreboot
+##
+default CONFIG_HAVE_HARD_RESET=1
+
+##
+## Build code to export a programmable irq routing table
+##
+default CONFIG_HAVE_PIRQ_TABLE=1
+default CONFIG_IRQ_SLOT_COUNT=11
+
+##
+## Build code to export an x86 MP table
+## Useful for specifying IRQ routing values
+##
+default CONFIG_HAVE_MP_TABLE=1
+
+## ACPI tables will be included
+default CONFIG_HAVE_ACPI_TABLES=0
+
+##
+## Build code to export a CMOS option table
+##
+default CONFIG_HAVE_OPTION_TABLE=1
+
+##
+## Move the default coreboot cmos range off of AMD RTC registers
+##
+default CONFIG_LB_CKS_RANGE_START=49
+default CONFIG_LB_CKS_RANGE_END=122
+default CONFIG_LB_CKS_LOC=123
+
+##
+## Build code for SMP support
+## Only worry about 2 micro processors
+##
+default CONFIG_SMP=1
+default CONFIG_MAX_PHYSICAL_CPUS=2
+default CONFIG_MAX_CPUS=4 * CONFIG_MAX_PHYSICAL_CPUS
+default CONFIG_LOGICAL_CPUS=1
+
+default CONFIG_SERIAL_CPU_INIT=0
+
+default CONFIG_ENABLE_APIC_EXT_ID=1
+default CONFIG_APIC_ID_OFFSET=0x00
+default CONFIG_LIFT_BSP_APIC_ID=1
+
+#memory hole size, 0 mean disable, others will enable the hole, at that case if it is small than mmio_basek, it will use mmio_basek instead. 
+#2G
+#default CONFIG_HW_MEM_HOLE_SIZEK=0x200000
+#1G
+default CONFIG_HW_MEM_HOLE_SIZEK=0x100000
+#512M
+#default CONFIG_HW_MEM_HOLE_SIZEK=0x80000
+
+#make auto increase hole size to avoid hole_startk equal to basek so as to make some kernel happy
+#default CONFIG_HW_MEM_HOLE_SIZE_AUTO_INC=1
+
+#VGA Console
+default CONFIG_CONSOLE_VGA=1
+default CONFIG_PCI_ROM_RUN=1
+
+#HT Unit ID offset, default is 1, the typical one, 0 mean only one HT device
+default CONFIG_HT_CHAIN_UNITID_BASE=1
+
+#real SB Unit ID, default is 0x20, mean dont touch it at last
+#default CONFIG_HT_CHAIN_END_UNITID_BASE=0x6
+
+#make the SB HT chain on bus 0, default is not (0)
+default CONFIG_SB_HT_CHAIN_ON_BUS0=2
+
+#only offset for SB chain?, default is yes(1)
+default CONFIG_SB_HT_CHAIN_UNITID_OFFSET_ONLY=0
+
+#allow capable device use that above 4G
+#default CONFIG_PCI_64BIT_PREF_MEM=1
+
+##
+## enable CACHE_AS_RAM specifics
+##
+default CONFIG_USE_DCACHE_RAM=1
+default CONFIG_DCACHE_RAM_BASE=0xc4000
+default CONFIG_DCACHE_RAM_SIZE=0x0c000
+default CONFIG_DCACHE_RAM_GLOBAL_VAR_SIZE=0x04000
+default CONFIG_USE_INIT=0
+
+default CONFIG_MEM_TRAIN_SEQ=2
+default CONFIG_WAIT_BEFORE_CPUS_INIT=0
+default CONFIG_AMDMCT = 1
+
+##
+## Build code to setup a generic IOAPIC
+##
+default CONFIG_IOAPIC=1
+
+##
+## Clean up the motherboard id strings
+##
+default CONFIG_MAINBOARD_PART_NUMBER="h8dmr (Fam10)"
+default CONFIG_MAINBOARD_VENDOR="Supermicro"
+default CONFIG_MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID=0x15d9
+default CONFIG_MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID=0x1511
+
+##
+## Set microcode patch file name
+##
+##      Barcelona rev Ax:  "mc_patch_01000020.h"
+##      Barcelona rev B0, B1, BA: "mc_patch_01000084.h"
+##      Barcelona rev B2, B3: "mc_patch_01000083.h"
+##			Shanghai rev RB-C2: "mc_patch_01000086.h"
+##			Shanghai rev DA-C2: "mc_patch_0100009f.h"
+##
+#default CONFIG_AMD_UCODE_PATCH_FILE="mc_patch_01000086.h"
+default CONFIG_AMD_UCODE_PATCH_FILE="mc_patch_0100009f.h"
+
+###
+### coreboot layout values
+###
+
+## CONFIG_ROM_IMAGE_SIZE is the amount of space to allow coreboot to occupy.
+default CONFIG_ROM_IMAGE_SIZE = 0x1e000
+
+##
+## Use a 32K stack
+##
+default CONFIG_STACK_SIZE=0x8000
+
+##
+## Use a 48K heap
+##
+default CONFIG_HEAP_SIZE=0xc0000
+
+##
+## Only use the option table in a normal image
+##
+default CONFIG_USE_OPTION_TABLE = (!CONFIG_USE_FALLBACK_IMAGE) && (!CONFIG_USE_FAILOVER_IMAGE )
+
+##
+## Coreboot C code runs at this location in RAM
+##
+default CONFIG_RAMBASE=0x00200000
+
+##
+## Load the payload from the ROM
+##
+default CONFIG_ROM_PAYLOAD = 1
+
+#default CONFIG_COMPRESSED_PAYLOAD = 1
+
+# CBFS will take care of payload compression
+default CONFIG_UNCOMPRESSED = 1
+
+###
+### Defaults of options that you may want to override in the target config file
+### 
+
+##
+## The default compiler
+##
+default CC="$(CONFIG_CROSS_COMPILE)gcc -m32"
+default HOSTCC="gcc"
+
+##
+## Disable the gdb stub by default
+## 
+default CONFIG_GDB_STUB=0
+
+##
+## The Serial Console
+##
+default CONFIG_USE_PRINTK_IN_CAR=1
+
+# To Enable the Serial Console
+default CONFIG_CONSOLE_SERIAL8250=1
+
+## Select the serial console baud rate
+default CONFIG_TTYS0_BAUD=115200
+#default CONFIG_TTYS0_BAUD=57600
+#default CONFIG_TTYS0_BAUD=38400
+#default CONFIG_TTYS0_BAUD=19200
+#default CONFIG_TTYS0_BAUD=9600
+#default CONFIG_TTYS0_BAUD=4800
+#default CONFIG_TTYS0_BAUD=2400
+#default CONFIG_TTYS0_BAUD=1200
+
+# Select the serial console base port
+default CONFIG_TTYS0_BASE=0x3f8
+
+# Select the serial protocol
+# This defaults to 8 data bits, 1 stop bit, and no parity
+default CONFIG_TTYS0_LCS=0x3
+
+##
+### Select the coreboot loglevel
+##
+## EMERG      1   system is unusable               
+## ALERT      2   action must be taken immediately 
+## CRIT       3   critical conditions              
+## ERR        4   error conditions                 
+## WARNING    5   warning conditions               
+## NOTICE     6   normal but significant condition 
+## INFO       7   informational                    
+## DEBUG      8   debug-level messages             
+## SPEW       9   Way too many details             
+
+## Request this level of debugging output
+default  CONFIG_DEFAULT_CONSOLE_LOGLEVEL=8
+## At a maximum only compile in this level of debugging
+default  CONFIG_MAXIMUM_CONSOLE_LOGLEVEL=9
+
+##
+## Select power on after power fail setting
+default CONFIG_MAINBOARD_POWER_ON_AFTER_POWER_FAIL="MAINBOARD_POWER_ON"
+
+default CONFIG_USE_FAILOVER_IMAGE=0
+default CONFIG_USE_FALLBACK_IMAGE=0
+default CONFIG_XIP_ROM_SIZE=CONFIG_FAILOVER_SIZE
+
+#
+# CBFS
+#
+#
+default CONFIG_CBFS=1
+
+### End Options.lb
+end
Index: src/mainboard/supermicro/h8dmr_fam10/mb_sysconf.h
===================================================================
--- src/mainboard/supermicro/h8dmr_fam10/mb_sysconf.h	(revision 0)
+++ src/mainboard/supermicro/h8dmr_fam10/mb_sysconf.h	(revision 0)
@@ -0,0 +1,34 @@ 
+/*
+ * This file is part of the coreboot project.
+ *
+ * Copyright (C) 2007 AMD
+ * Written by Yinghai Lu <yinghailu@amd.com> for AMD.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA  02110-1301 USA
+ */
+
+#ifndef MB_SYSCONF_H
+#define MB_SYSCONF_H
+
+struct mb_sysconf_t {
+	unsigned char bus_isa;
+	unsigned char bus_mcp55[8]; //1
+	unsigned apicid_mcp55;
+	unsigned bus_type[256]; 
+
+};
+
+#endif
+
Index: src/mainboard/supermicro/h8dmr_fam10/chip.h
===================================================================
--- src/mainboard/supermicro/h8dmr_fam10/chip.h	(revision 0)
+++ src/mainboard/supermicro/h8dmr_fam10/chip.h	(revision 0)
@@ -0,0 +1,25 @@ 
+/*
+ * This file is part of the coreboot project.
+ *
+ * Copyright (C) 2007 AMD
+ * Written by Yinghai Lu <yinghailu@amd.com> for AMD.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA  02110-1301 USA
+ */
+
+extern struct chip_operations mainboard_ops;
+
+struct mainboard_config {
+};
Index: src/mainboard/supermicro/h8dmr_fam10/apc_auto.c
===================================================================
--- src/mainboard/supermicro/h8dmr_fam10/apc_auto.c	(revision 0)
+++ src/mainboard/supermicro/h8dmr_fam10/apc_auto.c	(revision 0)
@@ -0,0 +1,137 @@ 
+/*
+ * This file is part of the coreboot project.
+ *
+ * Copyright (C) 2007 AMD
+ * Written by Yinghai Lu <yinghailu@amd.com> for AMD.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA  02110-1301 USA
+ */
+
+#define ASSEMBLY 1
+#define __ROMCC__
+
+#define RAMINIT_SYSINFO 1
+#define CACHE_AS_RAM_ADDRESS_DEBUG 0
+
+#define SET_NB_CFG_54 1 
+
+//used by raminit
+#define QRANK_DIMM_SUPPORT 1
+
+#define K8_REV_F_SUPPORT_F0_F1_WORKAROUND 0
+
+#include <stdint.h>
+#include <device/pci_def.h>
+#include <device/pci_ids.h>
+#include <arch/io.h>
+#include <device/pnp_def.h>
+#include <arch/romcc_io.h>
+#include <cpu/x86/lapic.h>
+#include "option_table.h"
+#include "pc80/mc146818rtc_early.c"
+#include "pc80/serial.c"
+
+#if CONFIG_USE_INIT == 0
+        #include "lib/memcpy.c"
+#endif
+
+#include "arch/i386/lib/console.c"
+#include "lib/uart8250.c"
+#include "console/vtxprintf.c"
+#include "./arch/i386/lib/printk_init.c"
+
+#if 0 
+static void post_code(uint8_t value) {
+#if 1
+        int i;
+        for(i=0;i<0x80000;i++) {
+                outb(value, 0x80);
+        }
+#endif
+}
+#endif
+
+#include <cpu/amd/model_fxx_rev.h>
+#include "northbridge/amd/amdk8/raminit.h"
+#include "cpu/amd/model_fxx/apic_timer.c"
+
+#include "lib/delay.c"
+
+//#include "cpu/x86/lapic/boot_cpu.c"
+#include "northbridge/amd/amdk8/reset_test.c"
+
+#include "northbridge/amd/amdk8/debug.c"
+
+#include "southbridge/nvidia/mcp55/mcp55_early_ctrl.c"
+
+#include "northbridge/amd/amdk8/amdk8_f.h"
+
+#include "cpu/x86/mtrr.h"
+#include "cpu/amd/mtrr.h"
+#include "cpu/x86/tsc.h"
+
+#include "northbridge/amd/amdk8/amdk8_f_pci.c"
+#include "northbridge/amd/amdk8/raminit_f_dqs.c"
+
+static inline unsigned get_nodes(void)
+{
+	return ((pci_read_config32(PCI_DEV(0, 0x18, 0), 0x60)>>4) & 7) + 1;
+}
+
+#include "cpu/amd/dualcore/dualcore.c"
+
+void hardwaremain(int ret_addr)
+{
+	struct sys_info *sysinfo = (DCACHE_RAM_BASE + DCACHE_RAM_SIZE - DCACHE_RAM_GLOBAL_VAR_SIZE); // in CACHE
+        struct sys_info *sysinfox = ((CONFIG_LB_MEM_TOPK<<10) - DCACHE_RAM_GLOBAL_VAR_SIZE); // in RAM
+
+	struct node_core_id id;
+
+	id = get_node_core_id_x();
+
+        print_debug("CODE IN CACHE ON NODE:"); print_debug_hex8(id.nodeid); print_debug("\r\n");
+
+	train_ram(id.nodeid, sysinfo, sysinfox);
+
+	/*
+		go back, but can not use stack any more, because we only keep ret_addr and can not restore esp, and ebp
+	*/
+
+        __asm__ volatile (
+                "movl  %0, %%edi\n\t"
+                "jmp     *%%edi\n\t"
+                :: "a"(ret_addr)
+        );
+
+
+
+}
+struct eregs {
+        uint32_t eax, ecx, edx, ebx, esp, ebp, esi, edi;
+        uint32_t vector;
+        uint32_t error_code;
+        uint32_t eip;
+        uint32_t cs;
+        uint32_t eflags;
+};
+
+void x86_exception(struct eregs *info)
+{
+        do {
+                hlt();
+        } while(1);
+}
+
+
Index: src/mainboard/supermicro/h8dmr_fam10/cmos.layout
===================================================================
--- src/mainboard/supermicro/h8dmr_fam10/cmos.layout	(revision 0)
+++ src/mainboard/supermicro/h8dmr_fam10/cmos.layout	(revision 0)
@@ -0,0 +1,119 @@ 
+## 
+## This file is part of the coreboot project.
+## 
+## Copyright (C) 2007 AMD
+## Written by Yinghai Lu <yinghailu@amd.com> for AMD.
+## 
+## This program is free software; you can redistribute it and/or modify
+## it under the terms of the GNU General Public License as published by
+## the Free Software Foundation; either version 2 of the License, or
+## (at your option) any later version.
+## 
+## This program is distributed in the hope that it will be useful,
+## but WITHOUT ANY WARRANTY; without even the implied warranty of
+## MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+## GNU General Public License for more details.
+## 
+## You should have received a copy of the GNU General Public License
+## along with this program; if not, write to the Free Software
+## Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA  02110-1301 USA
+## 
+
+entries
+
+#start-bit length  config config-ID    name
+#0            8       r       0        seconds
+#8            8       r       0        alarm_seconds
+#16           8       r       0        minutes
+#24           8       r       0        alarm_minutes
+#32           8       r       0        hours
+#40           8       r       0        alarm_hours
+#48           8       r       0        day_of_week
+#56           8       r       0        day_of_month
+#64           8       r       0        month
+#72           8       r       0        year
+#80           4       r       0        rate_select
+#84           3       r       0        REF_Clock
+#87           1       r       0        UIP
+#88           1       r       0        auto_switch_DST
+#89           1       r       0        24_hour_mode
+#90           1       r       0        binary_values_enable
+#91           1       r       0        square-wave_out_enable
+#92           1       r       0        update_finished_enable
+#93           1       r       0        alarm_interrupt_enable
+#94           1       r       0        periodic_interrupt_enable
+#95           1       r       0        disable_clock_updates
+#96         288       r       0        temporary_filler
+0          384       r       0        reserved_memory
+384          1       e       4        boot_option
+385          1       e       4        last_boot
+386          1       e       1        ECC_memory
+388          4       r       0        reboot_bits
+392          3       e       5        baud_rate
+395          1       e       1        hw_scrubber
+396          1       e       1        interleave_chip_selects
+397          2       e       8        max_mem_clock
+399          1       e       2        quad_core
+400          1       e       1        power_on_after_fail
+412          4       e       6        debug_level
+416          4       e       7        boot_first
+420          4       e       7        boot_second
+424          4       e       7        boot_third
+428          4       h       0        boot_index
+432	     8       h       0        boot_countdown
+440          4       e       9        slow_cpu
+444          1       e       1        nmi
+445          1       e       1        iommu
+728        256       h       0        user_data
+984         16       h       0        check_sum
+# Reserve the extended AMD configuration registers
+1000        24       r       0        reserved_memory1
+
+
+
+enumerations
+
+#ID value   text
+1     0     Disable
+1     1     Enable
+2     0     Enable
+2     1     Disable
+4     0     Fallback
+4     1     Normal
+5     0     115200
+5     1     57600
+5     2     38400
+5     3     19200
+5     4     9600
+5     5     4800
+5     6     2400
+5     7     1200
+6     6     Notice
+6     7     Info
+6     8     Debug
+6     9     Spew
+7     0     Network
+7     1     HDD
+7     2     Floppy
+7     8     Fallback_Network
+7     9     Fallback_HDD
+7     10    Fallback_Floppy
+#7     3     ROM
+8     0     200Mhz
+8     1     166Mhz
+8     2     133Mhz
+8     3     100Mhz
+9     0     off
+9     1     87.5%
+9     2     75.0%
+9     3     62.5%
+9     4     50.0%
+9     5     37.5%
+9     6     25.0%
+9     7     12.5%
+
+checksums
+
+checksum 392 983 984
+
+
Index: src/mainboard/supermicro/h8dmr_fam10/mainboard.c
===================================================================
--- src/mainboard/supermicro/h8dmr_fam10/mainboard.c	(revision 0)
+++ src/mainboard/supermicro/h8dmr_fam10/mainboard.c	(revision 0)
@@ -0,0 +1,31 @@ 
+/*
+ * This file is part of the coreboot project.
+ *
+ * Copyright (C) 2007 AMD
+ * Written by Yinghai Lu <yinghailu@amd.com> for AMD.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA  02110-1301 USA
+ */
+
+#include <console/console.h>
+#include <device/device.h>
+#include <device/pci.h>
+#include <device/pci_ids.h>
+#include <device/pci_ops.h>
+#include "chip.h"
+
+struct chip_operations mainboard_ops = {
+	CHIP_NAME("Supermicro H8DMR Mainboard (Family 10)")
+};
Index: src/mainboard/supermicro/h8dmr_fam10/get_bus_conf.c
===================================================================
--- src/mainboard/supermicro/h8dmr_fam10/get_bus_conf.c	(revision 0)
+++ src/mainboard/supermicro/h8dmr_fam10/get_bus_conf.c	(revision 0)
@@ -0,0 +1,138 @@ 
+/*
+ * This file is part of the coreboot project.
+ *
+ * Copyright (C) 2007 AMD
+ * Written by Yinghai Lu <yinghailu@amd.com> for AMD.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA  02110-1301 USA
+ */
+
+#include <console/console.h>
+#include <device/pci.h>
+#include <device/pci_ids.h>
+#include <string.h>
+#include <stdint.h>
+#if CONFIG_LOGICAL_CPUS==1
+#include <cpu/amd/dualcore.h>
+#endif
+
+#include <cpu/amd/amdfam10_sysconf.h>
+
+#include <stdlib.h>
+#include "mb_sysconf.h"
+
+// Global variables for MB layouts and these will be shared by irqtable mptable and acpi_tables
+struct mb_sysconf_t mb_sysconf;
+
+/* Here you only need to set value in pci1234 for HT-IO that could be
+installed or not You may need to preset pci1234 for HTIO board, please
+refer to src/northbridge/amd/amdfam10/get_pci1234.c for detail */
+static u32 pci1234x[] = {
+	0x0000ffc, 0x0000ffc, 0x0000ffc, 0x0000ffc, 0x0000ffc, 0x0000ffc,
+	0x0000ffc, 0x0000ffc, 0x0000ffc, 0x0000ffc, 0x0000ffc, 0x0000ffc,
+	0x0000ffc, 0x0000ffc, 0x0000ffc, 0x0000ffc, 0x0000ffc, 0x0000ffc,
+	0x0000ffc, 0x0000ffc, 0x0000ffc, 0x0000ffc, 0x0000ffc, 0x0000ffc,
+	0x0000ffc, 0x0000ffc, 0x0000ffc, 0x0000ffc, 0x0000ffc, 0x0000ffc,
+	0x0000ffc, 0x0000ffc,
+	};
+
+
+/* HT Chain device num, actually it is unit id base of every ht device
+in chain, assume every chain only have 4 ht device at most */
+
+static unsigned hcdnx[] = {
+	0x20202020, 0x20202020, 0x20202020, 0x20202020, 0x20202020,
+	0x20202020, 0x20202020, 0x20202020, 0x20202020, 0x20202020,
+	0x20202020, 0x20202020, 0x20202020, 0x20202020, 0x20202020,
+	0x20202020, 0x20202020, 0x20202020, 0x20202020, 0x20202020,
+	0x20202020, 0x20202020, 0x20202020, 0x20202020, 0x20202020,
+	0x20202020, 0x20202020, 0x20202020, 0x20202020, 0x20202020,
+	0x20202020, 0x20202020,
+};
+
+extern void get_pci1234(void);
+
+static unsigned get_bus_conf_done = 0;
+
+void get_bus_conf(void)
+{
+
+	unsigned apicid_base;
+	struct mb_sysconf_t *m;
+
+	device_t dev;
+	int i, j;
+
+	if(get_bus_conf_done==1) return; //do it only once
+
+	get_bus_conf_done = 1;
+
+	sysconf.mb = &mb_sysconf;
+
+	m = sysconf.mb;
+	memset(m, 0, sizeof(struct mb_sysconf_t));
+
+	sysconf.hc_possible_num = ARRAY_SIZE(pci1234x);
+	for(i=0;i<sysconf.hc_possible_num; i++) {
+		sysconf.pci1234[i] = pci1234x[i];
+		sysconf.hcdn[i] = hcdnx[i];
+	}
+
+	get_pci1234();
+
+	m->bus_type[0] = 1; //pci
+	sysconf.sbdn = (sysconf.hcdn[0] & 0xff); // first byte of first chain
+	m->bus_mcp55[0] = (sysconf.pci1234[0] >> 12) & 0xff;
+
+		/* MCP55 */
+		dev = dev_find_slot(m->bus_mcp55[0], PCI_DEVFN(sysconf.sbdn + 0x06,0));
+		if (dev) {
+			m->bus_mcp55[1] = pci_read_config8(dev, PCI_SECONDARY_BUS);
+		}
+		else {
+			printk_debug("ERROR - could not find PCI 1:%02x.0, using defaults\n", sysconf.sbdn + 0x06);
+		}
+
+		for(i=2; i<8;i++) {
+			dev = dev_find_slot(m->bus_mcp55[0], PCI_DEVFN(sysconf.sbdn + 0x0a + i - 2 , 0));
+			if (dev) {
+				m->bus_mcp55[i] = pci_read_config8(dev, PCI_SECONDARY_BUS);
+			}
+			else {
+				printk_debug("ERROR - could not find PCI %02x:%02x.0, using defaults\n", m->bus_mcp55[0], sysconf.sbdn + 0x0a + i - 2 );
+			}
+		}
+
+	for(i=0; i< sysconf.hc_possible_num; i++) {
+		if(!(sysconf.pci1234[i] & 0x1) ) continue;
+
+		unsigned busn = (sysconf.pci1234[i] >> 12) & 0xff;
+		unsigned busn_max = (sysconf.pci1234[i] >> 20) & 0xff;
+		for (j = busn; j <= busn_max; j++)
+			m->bus_type[j] = 1;
+		if(m->bus_isa <= busn_max)
+			m->bus_isa = busn_max + 1;
+		printk_debug("i=%d bus range: [%x, %x] bus_isa=%x\n",i, busn, busn_max, m->bus_isa);
+	}
+
+/*I/O APICs:	APIC ID	Version	State		Address*/
+#if CONFIG_LOGICAL_CPUS==1
+	apicid_base = get_apicid_base(1);
+#else
+	apicid_base = CONFIG_MAX_PHYSICAL_CPUS;
+#endif
+	m->apicid_mcp55 = apicid_base+0;
+
+}
Index: src/mainboard/supermicro/h8dmr_fam10/cache_as_ram_auto.c
===================================================================
--- src/mainboard/supermicro/h8dmr_fam10/cache_as_ram_auto.c	(revision 0)
+++ src/mainboard/supermicro/h8dmr_fam10/cache_as_ram_auto.c	(revision 0)
@@ -0,0 +1,380 @@ 
+/*
+ * This file is part of the coreboot project.
+ *
+ * Copyright (C) 2007 AMD
+ * Written by Yinghai Lu <yinghailu@amd.com> for AMD.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA  02110-1301 USA
+ */
+
+#define ASSEMBLY 1
+#define __ROMCC__
+
+#define RAMINIT_SYSINFO 1
+
+#define FAM10_SCAN_PCI_BUS 0
+#define FAM10_ALLOCATE_IO_RANGE 1
+
+#define QRANK_DIMM_SUPPORT 1
+
+#if CONFIG_LOGICAL_CPUS==1
+#define SET_NB_CFG_54 1
+#endif
+
+#define FAM10_SET_FIDVID 1
+#define FAM10_SET_FIDVID_CORE_RANGE 0
+
+#include <stdint.h>
+#include <string.h>
+#include <device/pci_def.h>
+#include <device/pci_ids.h>
+#include <arch/io.h>
+#include <device/pnp_def.h>
+#include <arch/romcc_io.h>
+#include <cpu/x86/lapic.h>
+#include "option_table.h"
+#include "pc80/mc146818rtc_early.c"
+
+// for enable the FAN
+#include "southbridge/nvidia/mcp55/mcp55_early_smbus.c"
+
+static void post_code(u8 value) {
+	outb(value, 0x80);
+}
+
+#if CONFIG_USE_FAILOVER_IMAGE==0
+#include "pc80/serial.c"
+#include "arch/i386/lib/console.c"
+#include "ram/ramtest.c"
+
+#include <cpu/amd/model_10xxx_rev.h>
+
+//#include "southbridge/nvidia/mcp55/mcp55_early_smbus.c"
+#include "northbridge/amd/amdfam10/raminit.h"
+#include "northbridge/amd/amdfam10/amdfam10.h"
+
+#endif
+
+#include "cpu/x86/lapic/boot_cpu.c"
+#include "northbridge/amd/amdfam10/reset_test.c"
+#include "superio/winbond/w83627hf/w83627hf_early_serial.c"
+#include "superio/winbond/w83627hf/w83627hf_early_init.c"
+
+#if CONFIG_USE_FAILOVER_IMAGE==0
+
+#include "cpu/x86/bist.h"
+
+#include "northbridge/amd/amdfam10/debug.c"
+
+#include "cpu/amd/mtrr/amd_earlymtrr.c"
+
+
+#include "northbridge/amd/amdfam10/setup_resource_map.c"
+
+#define SERIAL_DEV PNP_DEV(0x2e, W83627HF_SP1)
+
+#include "southbridge/nvidia/mcp55/mcp55_early_ctrl.c"
+
+static void memreset_setup(void)
+{
+}
+
+static void memreset(int controllers, const struct mem_controller *ctrl)
+{
+}
+
+static inline void activate_spd_rom(const struct mem_controller *ctrl)
+{
+	/* nothing to do */
+}
+
+static inline int spd_read_byte(unsigned device, unsigned address)
+{
+	return smbus_read_byte(device, address);
+}
+
+#include "northbridge/amd/amdfam10/amdfam10.h"
+#include "northbridge/amd/amdht/ht_wrapper.c"
+
+#include "include/cpu/x86/mem.h"
+#include "northbridge/amd/amdfam10/raminit_sysinfo_in_ram.c"
+#include "northbridge/amd/amdfam10/raminit_amdmct.c"
+#include "northbridge/amd/amdfam10/amdfam10_pci.c"
+
+#include "resourcemap.c" 
+
+#include "cpu/amd/quadcore/quadcore.c"
+
+#define MCP55_NUM 1
+#define MCP55_USE_NIC 1
+#define MCP55_USE_AZA 1
+
+#define MCP55_PCI_E_X_0 4
+
+#include "southbridge/nvidia/mcp55/mcp55_early_setup_ss.h"
+#include "southbridge/nvidia/mcp55/mcp55_early_setup_car.c"
+
+#include "cpu/amd/car/copy_and_run.c"
+
+#include "cpu/amd/car/post_cache_as_ram.c"
+
+#include "cpu/amd/model_10xxx/init_cpus.c"
+
+#include "cpu/amd/model_10xxx/fidvid.c"
+
+#endif
+
+#if ((CONFIG_HAVE_FAILOVER_BOOT==1) && (CONFIG_USE_FAILOVER_IMAGE == 1)) || ((CONFIG_HAVE_FAILOVER_BOOT==0) && (CONFIG_USE_FALLBACK_IMAGE == 1))
+
+#include "southbridge/nvidia/mcp55/mcp55_enable_rom.c"
+#include "northbridge/amd/amdfam10/early_ht.c"
+
+
+static void sio_setup(void)
+{
+
+        unsigned value;
+        uint32_t dword;
+        uint8_t byte;
+        enable_smbus();
+//	smbusx_write_byte(1, (0x58>>1), 0, 0x80); /* select bank0 */
+	smbusx_write_byte(1, (0x58>>1), 0xb1, 0xff); /* set FAN ctrl to DC mode */
+
+        byte = pci_read_config8(PCI_DEV(0, MCP55_DEVN_BASE+1 , 0), 0x7b);
+        byte |= 0x20; 
+        pci_write_config8(PCI_DEV(0, MCP55_DEVN_BASE+1 , 0), 0x7b, byte);
+        
+        dword = pci_read_config32(PCI_DEV(0, MCP55_DEVN_BASE+1 , 0), 0xa0);
+        dword |= (1<<0);
+        pci_write_config32(PCI_DEV(0, MCP55_DEVN_BASE+1 , 0), 0xa0, dword);
+        
+        dword = pci_read_config32(PCI_DEV(0, MCP55_DEVN_BASE+1 , 0), 0xa4);
+        dword |= (1<<16);
+        pci_write_config32(PCI_DEV(0, MCP55_DEVN_BASE+1 , 0), 0xa4, dword);
+
+}
+
+void failover_process(unsigned long bist, unsigned long cpu_init_detectedx)
+{
+        unsigned last_boot_normal_x = last_boot_normal();
+
+        /* Is this a cpu only reset? or Is this a secondary cpu? */
+        if ((cpu_init_detectedx) || (!boot_cpu())) {
+                if (last_boot_normal_x) {
+                        goto normal_image;
+                } else {
+                        goto fallback_image;
+                }
+        }
+
+        /* Nothing special needs to be done to find bus 0 */
+        /* Allow the HT devices to be found */
+
+        set_bsp_node_CHtExtNodeCfgEn();
+        enumerate_ht_chain();
+
+        sio_setup();
+
+        /* Setup the mcp55 */
+        mcp55_enable_rom();
+
+        /* Is this a deliberate reset by the bios */
+        if (bios_reset_detected() && last_boot_normal_x) {
+                goto normal_image;
+        }
+        /* This is the primary cpu how should I boot? */
+        else if (do_normal_boot()) {
+                goto normal_image;
+        }
+        else {
+                goto fallback_image;
+        }
+ normal_image:
+        __asm__ volatile ("jmp __normal_image"
+                : /* outputs */
+                : "a" (bist), "b" (cpu_init_detectedx) /* inputs */
+                );
+
+ fallback_image:
+#if CONFIG_HAVE_FAILOVER_BOOT==1
+        __asm__ volatile ("jmp __fallback_image"
+                : /* outputs */
+                : "a" (bist), "b" (cpu_init_detectedx) /* inputs */
+                )
+#endif
+	;
+}
+#endif
+void real_main(unsigned long bist, unsigned long cpu_init_detectedx);
+
+void cache_as_ram_main(unsigned long bist, unsigned long cpu_init_detectedx)
+{
+#if CONFIG_HAVE_FAILOVER_BOOT==1 
+    #if CONFIG_USE_FAILOVER_IMAGE==1
+	failover_process(bist, cpu_init_detectedx);	
+    #else
+	real_main(bist, cpu_init_detectedx);
+    #endif
+#else
+    #if CONFIG_USE_FALLBACK_IMAGE == 1
+	failover_process(bist, cpu_init_detectedx);	
+    #endif
+	real_main(bist, cpu_init_detectedx);
+#endif
+}
+
+#if CONFIG_USE_FAILOVER_IMAGE==0
+#include "spd_addr.h"
+#include "cpu/amd/microcode/microcode.c"
+#include "cpu/amd/model_10xxx/update_microcode.c"
+
+void real_main(unsigned long bist, unsigned long cpu_init_detectedx)
+{
+  struct sys_info *sysinfo = (struct sys_info *)(CONFIG_DCACHE_RAM_BASE + CONFIG_DCACHE_RAM_SIZE - CONFIG_DCACHE_RAM_GLOBAL_VAR_SIZE);
+
+	u32 bsp_apicid = 0;
+	u32 val;
+	u32 wants_reset;
+	msr_t msr;
+
+  post_code(0x30);
+ 
+        if (bist == 0) {
+		bsp_apicid = init_cpus(cpu_init_detectedx, sysinfo);
+        }
+
+  post_code(0x32);
+
+	pnp_enter_ext_func_mode(SERIAL_DEV);
+	pnp_write_config(SERIAL_DEV, 0x24, 0x84 | (1 << 6));
+ 	w83627hf_enable_dev(SERIAL_DEV, CONFIG_TTYS0_BASE);
+	pnp_exit_ext_func_mode(SERIAL_DEV);
+
+        uart_init();
+        console_init();
+  printk_debug("\n");
+
+
+	/* Halt if there was a built in self test failure */
+	report_bist_failure(bist);
+
+ val = cpuid_eax(1);
+ printk_debug("BSP Family_Model: %08x \n", val);
+ printk_debug("*sysinfo range: ["); print_debug_hex32((u32)sysinfo); print_debug(","); print_debug_hex32((u32)sysinfo+sizeof(struct sys_info)); print_debug("]\n");
+ printk_debug("bsp_apicid = %02x \n", bsp_apicid);
+ printk_debug("cpu_init_detectedx = %08x \n", cpu_init_detectedx);
+
+ /* Setup sysinfo defaults */
+ set_sysinfo_in_ram(0);
+
+ update_microcode(val);
+ post_code(0x33);
+
+ cpuSetAMDMSR();
+ post_code(0x34);
+
+ amd_ht_init(sysinfo);
+ post_code(0x35);
+
+ /* Setup nodes PCI space and start core 0 AP init. */
+ finalize_node_setup(sysinfo);
+
+ /* Setup any mainboard PCI settings etc. */
+ setup_mb_resource_map();
+ post_code(0x36);
+
+ /* wait for all the APs core0 started by finalize_node_setup. */
+ /* FIXME: A bunch of cores are going to start output to serial at once.
+  * It would be nice to fixup prink spinlocks for ROM XIP mode.
+  * I think it could be done by putting the spinlock flag in the cache
+  * of the BSP located right after sysinfo.
+  */
+
+        wait_all_core0_started();
+#if CONFIG_LOGICAL_CPUS==1
+ /* Core0 on each node is configured. Now setup any additional cores. */
+ printk_debug("start_other_cores()\n");
+        start_other_cores();
+ post_code(0x37);
+        wait_all_other_cores_started(bsp_apicid);
+#endif
+
+ post_code(0x38);
+
+#if FAM10_SET_FIDVID == 1
+ msr = rdmsr(0xc0010071);
+ printk_debug("\nBegin FIDVID MSR 0xc0010071 0x%08x 0x%08x \n", msr.hi, msr.lo);
+
+ /* FIXME: The sb fid change may survive the warm reset and only
+  * need to be done once.*/
+
+        enable_fid_change_on_sb(sysinfo->sbbusn, sysinfo->sbdn);
+ post_code(0x39);
+
+ if (!warm_reset_detect(0)) {      // BSP is node 0
+   init_fidvid_bsp(bsp_apicid, sysinfo->nodes);
+ } else {
+   init_fidvid_stage2(bsp_apicid, 0);  // BSP is node 0
+        }
+
+ post_code(0x3A);
+
+ /* show final fid and vid */
+ msr=rdmsr(0xc0010071);
+ printk_debug("End FIDVIDMSR 0xc0010071 0x%08x 0x%08x \n", msr.hi, msr.lo);
+#endif
+
+ wants_reset = mcp55_early_setup_x();
+
+ /* Reset for HT, FIDVID, PLL and errata changes to take affect. */
+ if (!warm_reset_detect(0)) {
+   print_info("...WARM RESET...\n\n\n");
+              	soft_reset();
+   die("After soft_reset_x - shouldn't see this message!!!\n");
+        }
+
+ if (wants_reset)
+   printk_debug("mcp55_early_setup_x wanted additional reset!\n");
+
+ post_code(0x3B);
+
+/* It's the time to set ctrl in sysinfo now; */
+printk_debug("fill_mem_ctrl()\n");
+fill_mem_ctrl(sysinfo->nodes, sysinfo->ctrl, spd_addr);
+
+post_code(0x3D);
+
+//printk_debug("enable_smbus()\n");
+//        enable_smbus(); /* enable in sio_setup */
+
+post_code(0x3E);
+
+        memreset_setup();
+
+post_code(0x40);
+
+
+ printk_debug("raminit_amdmct()\n");
+ raminit_amdmct(sysinfo);
+ post_code(0x41);
+
+// printk_debug("\n*** Yes, the copy/decompress is taking a while, FIXME!\n");
+ post_cache_as_ram();  // BSP switch stack to ram, copy then execute LB.
+ post_code(0x42);  // Should never see this post code.
+
+}
+
+
+#endif
Index: targets/supermicro/h8dmr_fam10/Config-abuild.lb
===================================================================
--- targets/supermicro/h8dmr_fam10/Config-abuild.lb	(revision 0)
+++ targets/supermicro/h8dmr_fam10/Config-abuild.lb	(revision 0)
@@ -0,0 +1,37 @@ 
+# This will make a target directory of ./VENDOR_MAINBOARD
+
+target VENDOR_MAINBOARD
+mainboard VENDOR/MAINBOARD
+
+option CC="CROSSCC"
+option CROSS_COMPILE="CROSS_PREFIX"
+option HOSTCC="CROSS_HOSTCC"
+
+__COMPRESSION__
+__LOGLEVEL__
+
+romimage "normal"
+        option USE_FAILOVER_IMAGE=0
+	option USE_FALLBACK_IMAGE=0
+	option ROM_IMAGE_SIZE=0x20000
+	option COREBOOT_EXTRA_VERSION=".0-normal"
+	payload __PAYLOAD__
+end
+
+romimage "fallback" 
+        option USE_FAILOVER_IMAGE=0
+	option USE_FALLBACK_IMAGE=1
+	option ROM_IMAGE_SIZE=0x20000
+	option COREBOOT_EXTRA_VERSION=".0-fallback"
+	payload __PAYLOAD__
+end
+
+romimage "failover"
+        option USE_FAILOVER_IMAGE=1
+        option USE_FALLBACK_IMAGE=0
+        option ROM_IMAGE_SIZE=FAILOVER_SIZE
+        option XIP_ROM_SIZE=FAILOVER_SIZE
+        option COREBOOT_EXTRA_VERSION=".0-failover"
+end
+
+buildrom ./coreboot.rom ROM_SIZE "normal" "fallback" "failover"
Index: targets/supermicro/h8dmr_fam10/Config.lb.kernel
===================================================================
--- targets/supermicro/h8dmr_fam10/Config.lb.kernel	(revision 0)
+++ targets/supermicro/h8dmr_fam10/Config.lb.kernel	(revision 0)
@@ -0,0 +1,75 @@ 
+##
+## This file is part of the coreboot project.
+##
+## Copyright (C) 2007 AMD
+## Written by Yinghai Lu <yinghailu@gmail.com> for AMD.
+##
+## This program is free software; you can redistribute it and/or modify
+## it under the terms of the GNU General Public License as published by
+## the Free Software Foundation; either version 2 of the License, or
+## (at your option) any later version.
+##
+## This program is distributed in the hope that it will be useful,
+## but WITHOUT ANY WARRANTY; without even the implied warranty of
+## MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+## GNU General Public License for more details.
+##
+## You should have received a copy of the GNU General Public License
+## along with this program; if not, write to the Free Software
+## Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA  02110-1301 USA
+##
+
+target h8dmr
+mainboard supermicro/h8dmr
+
+option ROM_SIZE=0x200000
+option FALLBACK_SIZE=(ROM_SIZE-0x1000)
+
+romimage "fallback" 
+	option USE_FAILOVER_IMAGE=0
+	option USE_FALLBACK_IMAGE=1
+	option CONFIG_COMPRESSED_PAYLOAD_LZMA=1
+	option CONFIG_PRECOMPRESSED_PAYLOAD=1
+#	option ROM_IMAGE_SIZE=0x19800
+	option ROM_IMAGE_SIZE=0x18000
+#	option ROM_IMAGE_SIZE=0x15800
+#	option ROM_IMAGE_SIZE=0x13800
+	option XIP_ROM_SIZE=0x40000
+	option COREBOOT_EXTRA_VERSION="$(shell cat ../../VERSION)_Fallback"
+#       payload ../../../payloads/tg3--ide_disk.zelf
+#        payload ../../../payloads/filo.elf
+#        payload ../../../payloads/filo_mem.elf
+#        payload ../../../payloads/filo.zelf
+#        payload ../../../payloads/tg3--filo_hda2.zelf
+#	payload ../../../payloads/tg3.zelf
+#	payload ../../../../payloads/tg3_vga.zelf
+#	payload ../../../../payloads/memtest
+#	payload ../../../../payloads/adlo.elf
+#	payload ../../../../payloads/e1000_vga.zelf
+#	payload ../../../../payloads/filo_hda.zelf
+#	payload ../../../../payloads/tg3--filo_hda2_vga.zelf
+#	payload ../../../../payloads/tg3--filo_hda2_vga_5_4.zelf
+#	payload ../../../../payloads/tg3--filo_hda2_vga_5.4.1.zelf
+#	payload ../../../../payloads/tg3--filo_hda2_vga_5.4.2.zelf
+	payload /home/yhlu/olpc-payload.elf.lzma
+#	payload ../../../../payloads/filo_hda.zelf
+#	payload ../../../../payloads/filo_hda2_novga.zelf
+#	payload ../../../payloads/tg3_com2.zelf
+#       payload ../../../payloads/e1000--filo.zelf
+#        payload ../../../payloads/tg3--e1000--filo.zelf
+#        payload ../../../payloads/tg3--eepro100--e1000--filo_hda2.zelf
+#	payload ../../../payloads/tg3--eepro100--e1000--filo_hda2_5.3.zelf
+#	payload ../../../payloads/tg3--eepro100--e1000--filo_hda2_com2.zelf
+end
+
+romimage "failover"
+	option USE_FAILOVER_IMAGE=1
+        option USE_FALLBACK_IMAGE=0
+        option ROM_IMAGE_SIZE=FAILOVER_SIZE
+        option XIP_ROM_SIZE=FAILOVER_SIZE
+        option COREBOOT_EXTRA_VERSION="$(shell cat ../../VERSION)_Failover"
+end
+
+
+buildrom ./coreboot.rom ROM_SIZE "fallback" "failover"
+#buildrom ./coreboot.rom ROM_SIZE "normal" "fallback" 
Index: targets/supermicro/h8dmr_fam10/Config.lb
===================================================================
--- targets/supermicro/h8dmr_fam10/Config.lb	(revision 0)
+++ targets/supermicro/h8dmr_fam10/Config.lb	(revision 0)
@@ -0,0 +1,42 @@ 
+##
+## This file is part of the coreboot project.
+##
+## Copyright (C) 2007 AMD
+## Written by Yinghai Lu <yinghailu@gmail.com> for AMD.
+##
+## This program is free software; you can redistribute it and/or modify
+## it under the terms of the GNU General Public License as published by
+## the Free Software Foundation; either version 2 of the License, or
+## (at your option) any later version.
+##
+## This program is distributed in the hope that it will be useful,
+## but WITHOUT ANY WARRANTY; without even the implied warranty of
+## MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+## GNU General Public License for more details.
+##
+## You should have received a copy of the GNU General Public License
+## along with this program; if not, write to the Free Software
+## Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA  02110-1301 USA
+##
+
+target h8dmr_fam10
+mainboard supermicro/h8dmr_fam10
+
+romimage "normal"
+  option COREBOOT_EXTRA_VERSION="$(shell cat ../../VERSION)_Normal"
+	payload ../payload.elf
+end
+
+romimage "fallback" 
+  option CONFIG_USE_FALLBACK_IMAGE=1
+  option COREBOOT_EXTRA_VERSION="$(shell cat ../../VERSION)_Fallback"
+	payload ../payload.elf
+end
+
+romimage "failover"
+  option CONFIG_USE_FAILOVER_IMAGE=1
+  option CONFIG_ROM_IMAGE_SIZE=CONFIG_FAILOVER_SIZE
+  option COREBOOT_EXTRA_VERSION="$(shell cat ../../VERSION)_Failover"
+end
+
+buildrom ./coreboot.rom CONFIG_ROM_SIZE "normal" "fallback" "failover"
Index: targets/supermicro/h8dmr_fam10/VERSION
===================================================================
--- targets/supermicro/h8dmr_fam10/VERSION	(revision 0)
+++ targets/supermicro/h8dmr_fam10/VERSION	(revision 0)
@@ -0,0 +1 @@ 
+_h8dmr
Index: targets/supermicro/h8dmr_fam10/Config-lab.lb
===================================================================
--- targets/supermicro/h8dmr_fam10/Config-lab.lb	(revision 0)
+++ targets/supermicro/h8dmr_fam10/Config-lab.lb	(revision 0)
@@ -0,0 +1,37 @@ 
+##
+## This file is part of the coreboot project.
+##
+## Copyright (C) 2007 AMD
+## Written by Yinghai Lu <yinghailu@gmail.com> for AMD.
+##
+## This program is free software; you can redistribute it and/or modify
+## it under the terms of the GNU General Public License as published by
+## the Free Software Foundation; either version 2 of the License, or
+## (at your option) any later version.
+##
+## This program is distributed in the hope that it will be useful,
+## but WITHOUT ANY WARRANTY; without even the implied warranty of
+## MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+## GNU General Public License for more details.
+##
+## You should have received a copy of the GNU General Public License
+## along with this program; if not, write to the Free Software
+## Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA  02110-1301 USA
+##
+
+target h8dmr_fam10
+mainboard supermicro/h8dmr_fam10
+
+romimage "fallback" 
+  option CONFIG_USE_FALLBACK_IMAGE=1
+  option COREBOOT_EXTRA_VERSION="$(shell cat ../../VERSION)_Fallback"
+	payload ../payload.elf
+end
+
+romimage "failover"
+  option CONFIG_USE_FAILOVER_IMAGE=1
+  option CONFIG_ROM_IMAGE_SIZE=CONFIG_FAILOVER_SIZE
+  option COREBOOT_EXTRA_VERSION="$(shell cat ../../VERSION)_Failover"
+end
+
+buildrom ./coreboot.rom CONFIG_ROM_SIZE "fallback" "failover"